Cite this article as: |
Anchalee Manonukul, Sukrit Songkuea, Pongporn Moonchaleanporn, and Makiko Tange, Effect of weld line positions on the tensile deformation of two-component metal injection moulding, Int. J. Miner. Metall. Mater., 24(2017), No. 12, pp. 1384-1393. https://doi.org/10.1007/s12613-017-1531-1 |
Anchalee Manonukul E-mail: anchalm@mtec.or.th
[1] |
D.F. Heaney, P. Suri, and R.M. German, Defect-free sintering of two material powder injection molded components. Part I Experimental investigations, J. Mater. Sci., 38(2003), No. 24, p. 4869.
|
[2] |
J.R. Alcock, P.M. Logan, and D.J. Stephenson, Surface engineering by co-injection moulding, Surf. Coat. Technol., 105(1998), No. 1-2, p. 65.
|
[3] |
P. Imgrund, A. Rota, F. Petzoldt, and A. Simchi, Manufacturing of multi-functional micro parts by two-component metal injection moulding, Int. J. Adv. Manuf. Technol., 33(2007), No. 1-2, p. 176.
|
[4] |
J.L. Johnson, L.K. Tan, R. Bollina, and R.M. German, Evaluation of copper powders for processing heat sinks by metal injection moulding, Powder Metall., 48(2005), No. 2, p. 123.
|
[5] |
P. Suri, Chapter 14-Two-material/two-color powder metal injection molding (C2-PIM),[in] Handbook of Metal Injection Moulding, Edited by Donald Heaney, Woodhead Publishing Limited, Oxford, 2012, p. 338.
|
[6] |
J.L. Johnson, L.K. Tan, P. Suri, and R.M. German, Design guidelines for processing bi-material components via powder-injection molding, JOM, 55(2003), No. 10, p. 30.
|
[7] |
A. Simchi, A. Rota, and P. Imgrund, An investigation on the sintering behavior of 316L and 17-4PH stainless steel powders for graded composites, Mater. Sci. Eng. A, 424(2006), No. 1-2, p. 282.
|
[8] |
M. Mulser, G. Veltl, and F. Petzoldt, Development of magnetic/non-magnetic stainless steel parts produced by two-component metal injection molding, Int. J. Precis. Eng. Manuf., 17(2016), No. 3, p. 347.
|
[9] |
T. Harikou, Y. Itoh, K. Satoh, and H. Miura, Joining of SUS316L and SUS430L by insert injection molding, J. Jpn. Soc. Powder Powder Metall., 49(2002), No. 9, p. 841.
|
[10] |
A. Islam, H. Hansen, M. Marhöfer, J. Angel, B. Dormann, and M. Bondo, Two-component micro injection moulding for hearing aid applications, Int. J. Adv. Manuf. Technol., 62(2012), No. 5-8, p. 605.
|
[11] |
V. Piotter, N. Holstein, K. Plewa, R.R. Ruprecht, and J. Hausselt, Replication of micro components by different variants of injection molding, Microsyst. Technol., 10(2004), No. 6-7, p. 547.
|
[12] |
MPIF standard 35:Materials Standard for Metal Injection Molded Parts, Metal Powder Industries Federation (MPIF), Princeton, NJ, 2016.
|
[13] |
MPIF Standard 42:Determination of Density of Compacted or Sintered Metal Powder Products, Metal Powder Industries Federation (MPIF), Princeton, NJ, 2000.
|
[14] |
V. Firouzdor, A. Simchi, and A.H. Kokabi, An investigation of the densification and microstructural evolution of M2/316L stepwise graded composite during co-sintering, J. Mater. Sci., 43(2008), No. 1, p. 55.
|
[15] |
V. Firouzdor and A. Simchi, Co-sintering of M2/17-4PH powders for fabrication of functional graded composite layers, J. Compos. Mater., 44(2010), No. 4, p. 417.
|
[16] |
D. Ravi and D.J. Green, Sintering stresses and distortion produced by density differences in bi-layer structures, J. Eur. Ceram. Soc., 26(2006), No. 1-2, p. 17.
|
[17] |
P. Suri, D.F. Heaney, and R.M. German, Defect-free sintering of two material powder injection molded components. Part Ⅱ Model, J. Mater. Sci., 38(2003), No. 24, p. 4875.
|
[18] |
P. Imgrund, A. Rota, and A. Simchi, Microinjection moulding of 316L/17-4PH and 316L/Fe powders for fabrication of magnetic-nonmagnetic bimetals, J. Mater. Process. Technol., 200(2008), No. 1-3, p. 259.
|
[19] |
Y.M. Li, L.J. Li, and K.A. Khalil, Effect of powder loading on metal injection molding stainless steels, J. Mater. Process. Technol., 183(2007), No. 2-3, p. 432.
|