Effects of initial grain size and strain on grain boundary engineering of high-nitrogen CrMn austenitic stainless steel

Zhen-hua Wang; Jian-jun Qi; Wan-tang Fu

doi:10.1007/s12613-018-1641-4

Volume 25 Issue 8

Aug. 2018

Turn off MathJax

数据统计

计量

文章访问数: 364
HTML全文浏览量: 39
PDF下载量: 16
被引次数: 0

文章导航 > 矿物冶金与材料学报（英文） > 2018 > 25(8): 922-929

Zhen-hua Wang, Jian-jun Qi, and Wan-tang Fu, Effects of initial grain size and strain on grain boundary engineering of high-nitrogen CrMn austenitic stainless steel, Int. J. Miner. Metall. Mater., 25(2018), No. 8, pp. 922-929. https://doi.org/10.1007/s12613-018-1641-4

Cite this article as:

Zhen-hua Wang, Jian-jun Qi, and Wan-tang Fu, Effects of initial grain size and strain on grain boundary engineering of high-nitrogen CrMn austenitic stainless steel, Int. J. Miner. Metall. Mater., 25(2018), No. 8, pp. 922-929. https://doi.org/10.1007/s12613-018-1641-4

Citation:

PDF( 4340 KB)

引用本文 PDF XML SpringerLink

研究论文

Effects of initial grain size and strain on grain boundary engineering of high-nitrogen CrMn austenitic stainless steel

School of Mechanical Engineering, Yanshan University, Qinhuangdao 066004, China
State Key Laboratory of Metastable Materials Science and Technology, Yanshan University, Qinhuangdao 066004, China
HBIS Group Technology Research Institute, Shijiazhuang 050023, China

通讯作者:
Zhen-hua Wang E-mail: wangzhenhua@ysu.edu.cn

中文摘要

18Mn18Cr0.5N steel with an initial grain size of 28–177 μm was processed by 2.5%–20% cold rolling and annealing at 1000℃ for 24 h, and the grain boundary character distribution was examined via electron backscatter diffraction. Low strain (2.5%) favored the formation of low-Σ boundaries. At this strain, the fraction of low-Σ boundaries was insensitive to the initial grain size. However, specimens with fine initial grains showed decreasing grain size after grain boundary engineering processing. The fraction of low-Σ boundaries and the (Σ9 + Σ27)/Σ3 value decreased with increasing strain; furthermore, the specimens with fine initial grain size were sensitive to the strain. Finally, the effects of the initial grain size and strain on the grain boundary engineering were discussed in detail.

关键词:

Research Article

Effects of initial grain size and strain on grain boundary engineering of high-nitrogen CrMn austenitic stainless steel

+ Author Affiliations

Abstract

Abstract

18Mn18Cr0.5N steel with an initial grain size of 28–177 μm was processed by 2.5%–20% cold rolling and annealing at 1000℃ for 24 h, and the grain boundary character distribution was examined via electron backscatter diffraction. Low strain (2.5%) favored the formation of low-Σ boundaries. At this strain, the fraction of low-Σ boundaries was insensitive to the initial grain size. However, specimens with fine initial grains showed decreasing grain size after grain boundary engineering processing. The fraction of low-Σ boundaries and the (Σ9 + Σ27)/Σ3 value decreased with increasing strain; furthermore, the specimens with fine initial grain size were sensitive to the strain. Finally, the effects of the initial grain size and strain on the grain boundary engineering were discussed in detail.
- grain boundary engineering;
- grain boundary character distribution;
- grain size;
- strain;
- austenitic stainless steel

FullText(HTML)

Supplements(0)

References(27)

References

[1]	V. Randle, Mechanism of twinning-induced grain boundary engineering in low stacking-fault energy materials, Acta Mater., 47(1999), No. 15-16, p. 4187.
[2]	T. Watanabe, Grain boundary engineering: historical perspective and future prospects, J. Mater. Sci., 46(2011), No. 12, p. 4095.
[3]	V. Randle, Twinning-related grain boundary engineering, Acta Mater., 52(2004), No. 14, p. 4067.
[4]	Z.W. Zhang, W.H. Wang, Y. Zhou, I. Baker, D. Chen, and Y.F. Liang, Control of grain boundary character distribution and its effects on the deformation of Fe–6.5wt.% Si, J. Alloys Compd., 639(2015), p. 40.
[5]	S. Kobayashi, T. Maruyama, S. Tsurekawa, and T. Watanabe, Grain boundary engineering based on fractal analysis for control of segregation-induced intergranular brittle fracture in polycrystalline nickel, Acta Mater., 60(2012), No. 17, p. 6200.
[6]	S. Kobayashi, T. Maruyama, S. Saito, S. Tsurekawa, and T. Watanabe, In situ observation of crack propagation and role of grain boundary microstructure in nickel embrittled by sulfur, J. Mater. Sci., 49(2014), No. 11, p. 4007.
[7]	R. Jones and V. Randle, Sensitisation behaviour of grain boundary engineered austenitic stainless steel, Mater. Sci. Eng. A, 527(2010), No. 16-17, p. 4275.
[8]	F. Shi, P.C. Tian, N. Jia, Z.H. Ye, Y. Qi, C.M. Liu, and X.W. Li, Improving intergranular corrosion resistance in a nickel-free and manganese-bearing high-nitrogen austenitic stainless steel through grain boundary character distribution optimization, Corros. Sci., 107(2016), p. 49.
[9]	E.A. West and G.S. Was, IGSCC of grain boundary engineered 316L and 690 in supercritical water, J. Nucl. Mater., 392(2009), No. 2, p. 264.
[10]	T.G. Liu, S. Xia, H. Li, B.X. Zhou, and Q. Bai, The highly twinned grain boundary network formation during grain boundary engineering, Mater. Lett., 133(2014), p. 97.
[11]	D. Horton, C.B. Thomson, and V. Randle, Aspects of twinning and grain growth in high purity and commercially pure nickel, Mater. Sci. Eng. A, 203(1995), No. 1-2, p. 408.
[12]	W. Cao, S. Xia, Q. Bai, W.Z. Zhang, B.X. Zhou, Z.J. Li, and L. Jiang, Effects of initial microstructure on the grain boundary network during grain boundary engineering in Hastelloy N alloy, J. Alloys Compd., 704(2017), p. 724.
[13]	M. Detrois, J. Rotella, R.L. Goetz, R.C. Helmink, and S. Tin, Grain boundary engineering of powder processed Ni-based superalloy RR1000: Influence of the deformation parameters, Mater. Sci. Eng. A, 627(2015), p. 95.
[14]	K. Kurihara, H. Kokawa, S. Sato, Y.S. Sato, H.T. Fuji, and M. Kawai, Grain boundary engineering of titanium-stabilized 321 austenitic stainless steel, J. Mater. Sci., 46(2011), No. 12, p. 4270.
[15]	M. Shimada, H. Kokawa, Z.J. Wang, Y.S. Sato, and I. Karibe, Optimization of grain boundary character distribution for intergranular corrosion resistant 304 stainless steel by twin-induced grain boundary engineering, Acta Mater., 50(2002), No. 9, p. 2331.
[16]	B. Li and S. Tin, The role of deformation temperature and strain on grain boundary engineering of Inconel 600, Mater. Sci. Eng. A, 603(2014), p. 104.
[17]	H. Akhiani, M. Nezakat, M. Sanayei, and J. Szunar, The effect of thermo-mechanical processing on grain boundary character distribution in Incoloy 800H/HT, Mater. Sci. Eng. A, 626(2015), p. 51.
[18]	H. Kokawa, W.Z. Jin, Z.J. Wang, M. Michiuchi, Y.S. Sato, W. Dong, and Y. Katada, Grain boundary engineering of high-nitrogen austenitic stainless steel, Mater. Sci. Forum, 539-543(2007), No. 5, p. 4962.
[19]	D.G. Brandon, The structure of high-angle grain boundaries, Acta Metall., 14(1966), No. 11, p. 1479.
[20]	E.M. Lehockey, A.M. Brennenstuhl, and I. Thompson, On the relationship between grain boundary connectivity, coincident site lattice boundaries, and intergranular stress corrosion cracking, Corros. Sci., 46(2004), No. 10, p. 2383.
[21]	S. Mandal, A.K. Bhaduri, and V. Subramanya Sarma, Grain boundary engineering in alloy D9 through thermo-mechanical processing: influence of process variables and aspects of micro-mechanisms, Int. J. Adv. Eng. Sci. Appl. Math., 2(2010), No. 4, p. 149.
[22]	S. Tokita, H. Kokawa, Y.S. Sato, and H.T. Fuji, In situ EBSD observation of grain boundary character distribution evolution during thermomechanical process used for grain boundary engineering of 304 austenitic stainless steel, Mater. Charact., 131(2017), p. 31.
[23]	Z.H. Wang, X.Z. Ning, Q. Meng, S.H. Sun, and W.T. Fu. A new insight into manufacturing fine-grained heavy retaining rings, Mater. Des., 103(2016), p. 152.
[24]	M. Ojima, Y. Adachi, Y. Tomota, Y. Katada, Y. Kaneko, K. Kuroda, and H. Saka, Weak beam TEM study on stacking fault energy of high nitrogen steels, Steel Res. Int., 80(2009), No. 7, p. 477.
[25]	V. Randle and M. Coleman, A study of low-strain and medium-strain grain boundary engineering, Acta Mater., 57(2009), No. 11, p. 3410.
[26]	H.B. Li, Z.H. Jiang, Z.R. Zhang, and Y. Yang, Effect of grain size on mechanical properties of nickel-free high nitrogen austenitic stainless steel, J. Iron Steel Res. Int., 16(2009), No. 1, p. 58.
[27]	J.T. Shi, L.G. Hou, J.R. Zuo, L.Z. Zhuang, and J.S. Zhang, Effect of cryogenic rolling and annealing on the microstructure evolution and mechanical properties of 304 stainless steel, Int. J. Miner. Metall. Mater., 24(2017), No. 6, p. 638.

Relative Articles

Cited By

Proportional views

数据统计

姓名
邮箱
手机号码
标题
留言内容
验证码

留言板

数据统计

分享

计量

Effects of initial grain size and strain on grain boundary engineering of high-nitrogen CrMn austenitic stainless steel

中文摘要

Effects of initial grain size and strain on grain boundary engineering of high-nitrogen CrMn austenitic stainless steel

Abstract

References

数据统计

Catalog