Preparation of rare-earth-modified medical stone powders and their application as conductive fillers

Li-ying Qi; Su-e Hao; Tian-cheng Sun

doi:10.1007/s12613-019-1731-y

Volume 26 Issue 2

Feb. 2019

Turn off MathJax

数据统计

计量

文章访问数: 451
HTML全文浏览量: 90
PDF下载量: 8
被引次数: 0

文章导航 > 矿物冶金与材料学报（英文） > 2019 > 26(2): 260-266

Li-ying Qi, Su-e Hao, and Tian-cheng Sun, Preparation of rare-earth-modified medical stone powders and their application as conductive fillers, Int. J. Miner. Metall. Mater., 26(2019), No. 2, pp. 260-266. https://doi.org/10.1007/s12613-019-1731-y

Cite this article as:

Li-ying Qi, Su-e Hao, and Tian-cheng Sun, Preparation of rare-earth-modified medical stone powders and their application as conductive fillers, Int. J. Miner. Metall. Mater., 26(2019), No. 2, pp. 260-266. https://doi.org/10.1007/s12613-019-1731-y

Citation:

PDF( 332 KB)

引用本文 PDF XML SpringerLink

研究论文

Preparation of rare-earth-modified medical stone powders and their application as conductive fillers

School of Chemistry and Chemical Engineering, Harbin Institute of Technology, Harbin 150001, China

通讯作者:
Su-e Hao E-mail: haosue@hit.edu.cn

中文摘要

Traditional metal conductive fillers are expensive and prone to oxidation. Thus, the development of new conductive powders as fillers is urgently needed. A novel gaseous penetration technology was adopted to prepare La-doped medical stone powders (La-MSPs), which are inexpensive mesoporous materials, as a new kind of conductive filler material. The prepared La-MSPs attained a resistivity of 450 Ω·m and were used as a filler to prepare conductive coatings with epoxy resin as the resin matrix. The influence of the La-MSPs dosage on the resistance and hardness of the coatings was also determined. The resistance and the hardness both decreased with increasing filler dosage. Finally, the optimum recipe of the conductive coatings with the most suitable fillers dosage (55wt%) was obtained. The hardness and resistance of the coatings with 55wt% La-MSPs were HV 4 and 5.5×10⁷ Ω, respectively.

关键词:

Research Article

Preparation of rare-earth-modified medical stone powders and their application as conductive fillers

+ Author Affiliations

Abstract

Abstract

Traditional metal conductive fillers are expensive and prone to oxidation. Thus, the development of new conductive powders as fillers is urgently needed. A novel gaseous penetration technology was adopted to prepare La-doped medical stone powders (La-MSPs), which are inexpensive mesoporous materials, as a new kind of conductive filler material. The prepared La-MSPs attained a resistivity of 450 Ω·m and were used as a filler to prepare conductive coatings with epoxy resin as the resin matrix. The influence of the La-MSPs dosage on the resistance and hardness of the coatings was also determined. The resistance and the hardness both decreased with increasing filler dosage. Finally, the optimum recipe of the conductive coatings with the most suitable fillers dosage (55wt%) was obtained. The hardness and resistance of the coatings with 55wt% La-MSPs were HV 4 and 5.5×10⁷ Ω, respectively.
- chemical engineering;
- conductive materials;
- rare earths;
- medical stone powders;
- gaseous penetration technology

FullText(HTML)

Supplements(0)

References(29)

References

[1]	G.Z. Li, L.J. Feng, P.R. Tong, and Z. Zhai, The properties of MWCNT/polyurethane conductive composite coating prepared by electrostatic spraying, Prog. Org. Coat., 90(2016), p. 284.
[2]	M. Mobin, J. Aslam, and R. Alam, Anti-corrosive properties of Poly(aniline-co-2,3-xylidine)/ZnO nanocomposite coating on low-carbon steel, J. Adhes. Sci. Technol., 31(2017), No. 7, p. 749.
[3]	Q.L. Wen, W.C. Zhou, J.B. Su, Y.C. Qing, F. Luo, and D.M. Zhu, High performance electromagnetic interference shielding of lamellar MoSi₂/glass composite coatings by plasma spraying, J. Alloys Compd., 666(2016), p. 359.
[4]	R.D. Farahani, M. Gagne, J.E. Klemberg-Sapieha, and T. Daniel, Electrically conductive silver nanoparticles-filled nanocomposite materials as surface coatings of composite structures, Adv. Eng. Mater., 18(2016), No. 7, p. 1189.
[5]	X.Z. Gao, H.J. Liu, F. Cheng, and Y. Chen, Thermoresponsive polyaniline nanoparticles:Preparation, characterization, and their potential application in waterborne anticorrosion coatings, Chem. Eng. J., 283(2016), p. 682.
[6]	H. Singh, T.S. Sidhu, and S.B.S. Kalsi, Behavior of Ni-based superalloys in an actual waste incinerator plant under cyclic conditions for 1000 h at 900℃, Corrosion, 70(2014), No. 12, p. 1249.
[7]	M. Abbasi and M.M. Verdian, Processing and properties of CuAl₂ intermetallic coatings, Surf. Eng., 33(2017), No. 3, p. 186.
[8]	C. Guo, H.J. Duan, C.Y. Dong, G.Z. Zhao, Y.Q. Liu, and Y.Q. Yang, Preparation of the polypropylene/nickel coated glass fibers conductive composites with a low percolation threshold, Mater. Lett., 143(2015), p. 124.
[9]	M.M. Momeni, S. Hashemizadeh, M. Mirhosseini, A. Kazempour, and S.A. Hosseinizadeh, Preparation, characterisation, hardness and antibacterial properties of Zn-Ni-TiO₂ nanocomposites coatings, Surf. Eng., 32(2016), No. 7, p. 490.
[10]	M. Jafari, A. Rahimi, P. Shokrolahi, and A.E. Langroudi, Synthesis of antistatic hybrid nanocomposite coatings using surface modified indium tin oxide (ITO) nanoparticles, J. Coat. Technol. Res., 11(2014), No. 4, p. 587.
[11]	C.C. Chang, F. Hwang, C.Y. Hsieh, C.C. Chen, and L.P. Cheng, Preparation and characterization of polymer/zirconia nanocomposite antistatic coatings on plastic substrates, J. Coat. Technol. Res., 10(2013), No. 1, p. 73.
[12]	Q.Y. Shang, S.E. Hao, W.L. Wang, D.S. Fu, and T.L. Ma, Preparation and characterization of antistatic coatings with modified BaTiO₃ powders as conductive fillers, J. Adhes. Sci. Technol., 27(2013), p. 2642.
[13]	L.H. Yu, T. Huang, and J.H Xu, Microstructure, mechanical and tribological properties of TaCN composite films, Surf. Eng., 33(2017), No. 1, p. 1.
[14]	F.W. Wang, C.Q. Cui, S.T. Zhang, and J. Wang, Influences of copper roughness on the electrical and mechanical performances of embedded capacitance materials, J. Adhes. Sci. Technol., 30(2017), No. 12, p. 1364.
[15]	S.Y. Meng, H.B. Wu, S.P. Wu, and Y.X. Tang, Preparation of ultrafine silver powder and its electrical properties, Electron. Compon. Mater., 23(2004), No. 7, p. 35.
[16]	H.J. Jiang, K.S. Moon, Y. Li, and C. Wong, Surface functionalized silver nanoparticles for ultrahigh conductive polymer composites, Chem. Mater., 18(2006), No. 13, p. 1969.
[17]	C. Zhuang and Z. Li, Mechanical characterisation of Si-C-N thin films prepared by electron cyclotron resonance plasma chemical vapour deposition at low microwave power and low temperature, Surf. Eng., 32(2016), No. 11, p. 1.
[18]	S.R. Anvari, S.M. Monirvaghefi, and M.H. Enayati, Wear characteristics of functionally graded nanocrystalline Ni-P coatings, Surf. Eng., 31(2015), No. 9, p. 693.
[19]	T.P. Gao, W.B. Wang, and A.Q. Wang, A pH-sensitive composite hydrogel based on sodium alginate and medical stone:synthesis, swelling, and heavy metal ions adsorption properties, Macromol. Res., 19(2011), No. 7, p. 739.
[20]	R.Q. Gao and X.M. Hou, Preparation and photo-catalytic activity of TiO₂-coated medical stone-based porous ceramics, Int. J. Miner. Metall. Mater., 20(2013), No. 6, p. 593.
[21]	J.L. Li, S.E. Hao, D.S. Fu, W. Wang, T.L. Ma, and C.Y. Wang, Modification of Ag-doped BaTiO₃ powders through La gaseous penetration route, J. Rare Earths, 28(2010), p. 154.
[22]	F.W. Wang, S.E. Hao, J.L. Li, J.T. Wang, Y. Gao, Y.F. Shen, and S.Y. Wang, Significant modiﬁcation to Bi-doped BaTiO₃ by Sm in gaseous penetration process, J. Mater. Sci. Mater. Electron., 25(2014), No. 8, p. 3543.
[23]	J.L. Li, S.E. Hao, F.W. Wang, Y. Gao, J.T. Wang, and Y.F. Shen, Significant promotion to electrical properties of Sm modified BaLa_xSm_xTiO₃ (0.001 ≤ x ≤ 0.005) powders:A novel precursor gaseous penetration route, Sci. Adv. Mater., 7(2015), No. 1, p. 35.
[24]	D.S. Fu, S.E. Hao, J.L. Li, and L.S. Qiang, Effects of the penetration temperature on structure and electrical conductivity of samarium modified BaTiO₃ powders, J. Rare Earths, 29(2011), No. 2, p. 164.
[25]	Y.J. Li, S.E. Hao, F.W. Wang, X.R. Liu, and X.W. Meng, Investigation on relationship among calcination temperature, grain size, Mn valence and resistivity of Ca_0.75Er_0.25MnO_3-δ powders, J. Mater. Sci. Mater. Electron., 26(2015), No. 1, p. 176.
[26]	X.W. Meng, S.E. Hao, J.L. Li, Q.Y. Fu, and D.S. Fu, Preparation of Ca_0.8Sm_0.2MnO₃ powders and effects of calcination temperature on structure and electrical property, Powder Technol., 224(2012), p. 96.
[27]	P.J.M. Carrott and K.S.W. Sing, Assessment of microporosity, Stud. Surf. Sci. Catal., 9(1988), p. 77.
[28]	T. Matthias, K. Katsumi, V.N. Alexander, P.O. James, R.R. Francisco, R. Jean, and S.W.S. Kenneth, Physisorption of gases, with special reference to the evaluation of surface area and pore size distribution (IUPAC Technical Report), Pure Appl. Chem., 87(2015), No. 9-10, p. 1051.
[29]	E.A. Prasetyanto, S. Sujandi, S.C. Lee, and S.E. Park, Highly dispersed CuO nanoparticles on SBA-16 type mesoporous silica with cyclam SBA-16 as a precursor, Bull. Korean Chem. Soc., 28(2007), No. 12, p. 2359.

Relative Articles

Cited By

Proportional views

数据统计

姓名
邮箱
手机号码
标题
留言内容
验证码

留言板

数据统计

分享

计量

Preparation of rare-earth-modified medical stone powders and their application as conductive fillers

中文摘要

Preparation of rare-earth-modified medical stone powders and their application as conductive fillers

Abstract

References

数据统计

Catalog