Effect of Cr content and cooling rate on the primary phase of Al-2.5Mn alloy

Hang-qi Feng; Zhi-bo Yang; Ye-tong Bai; Li Zhang; Yu-lin Liu

doi:10.1007/s12613-019-1862-1

Volume 26 Issue 12

Dec. 2019

Turn off MathJax

数据统计

计量

文章访问数: 662
HTML全文浏览量: 112
PDF下载量: 20
被引次数: 0

文章导航 > 矿物冶金与材料学报（英文） > 2019 > 26(12): 1551-1558

Hang-qi Feng, Zhi-bo Yang, Ye-tong Bai, Li Zhang, and Yu-lin Liu, Effect of Cr content and cooling rate on the primary phase of Al-2.5Mn alloy, Int. J. Miner. Metall. Mater., 26(2019), No. 12, pp. 1551-1558. https://doi.org/10.1007/s12613-019-1862-1

Cite this article as:

Hang-qi Feng, Zhi-bo Yang, Ye-tong Bai, Li Zhang, and Yu-lin Liu, Effect of Cr content and cooling rate on the primary phase of Al-2.5Mn alloy, Int. J. Miner. Metall. Mater., 26(2019), No. 12, pp. 1551-1558. https://doi.org/10.1007/s12613-019-1862-1

Citation:

PDF( 6278 KB)

引用本文 PDF XML SpringerLink

研究论文

Effect of Cr content and cooling rate on the primary phase of Al-2.5Mn alloy

School of Materials Science and Engineering, Shenyang Aerospace University, Shenyang 110136, China

通讯作者:
Yu-lin Liu E-mail: ylliu@sau.edu.cn

中文摘要

The effect of Cr content and cooling rate on the microstructure of Al-Mn alloy was studied using well resistance furnace melting, and the alloy was analyzed using scanning electron microscopy (SEM) and X-ray diffraction (XRD). The experimental results showed that adding Cr could significantly improve the morphology of the primary phase in the Al-2.5Mn alloy. Without Cr, the primary phase in the alloy was thick, needle-like, and strip-like structure. After adding 0.2wt%-0.5wt% Cr, the primary phase in the upper part of the alloy was gradually fined and reached the best effect at 0.35wt% Cr. When the content of Cr was 0.5wt%, the microstructure of the primary phase in the upper part began to coarsen. The bottom of the alloy was a large bulk phase, but still much finer than that without adding Cr. XRD and SEM analysis showed that the precipitation phase at the bottom was mainly Al₈₅Mn₇Cr₈, while the fine microstructure at the top was Al₆Mn and Al₃Mn. The results of the cooling rate experiments showed that the primary phase of Al-2.5Mn-0.35Cr was further refined, and the eutectic microstructure was partly achieved, under air-cooling condition. And when the cooling method was iron die-cooling, the microstructure of the Al-2.5Mn-0.35Cr alloy was changed into a eutectic microstructure.

关键词:

Research Article

Effect of Cr content and cooling rate on the primary phase of Al-2.5Mn alloy

+ Author Affiliations

Abstract

Abstract

The effect of Cr content and cooling rate on the microstructure of Al-Mn alloy was studied using well resistance furnace melting, and the alloy was analyzed using scanning electron microscopy (SEM) and X-ray diffraction (XRD). The experimental results showed that adding Cr could significantly improve the morphology of the primary phase in the Al-2.5Mn alloy. Without Cr, the primary phase in the alloy was thick, needle-like, and strip-like structure. After adding 0.2wt%-0.5wt% Cr, the primary phase in the upper part of the alloy was gradually fined and reached the best effect at 0.35wt% Cr. When the content of Cr was 0.5wt%, the microstructure of the primary phase in the upper part began to coarsen. The bottom of the alloy was a large bulk phase, but still much finer than that without adding Cr. XRD and SEM analysis showed that the precipitation phase at the bottom was mainly Al₈₅Mn₇Cr₈, while the fine microstructure at the top was Al₆Mn and Al₃Mn. The results of the cooling rate experiments showed that the primary phase of Al-2.5Mn-0.35Cr was further refined, and the eutectic microstructure was partly achieved, under air-cooling condition. And when the cooling method was iron die-cooling, the microstructure of the Al-2.5Mn-0.35Cr alloy was changed into a eutectic microstructure.
- Al-2.5Mn alloy;
- Cr content;
- primary phase;
- cooling rate

FullText(HTML)

Supplements(0)

References(32)

References

[1]	J. Sun, S.X. Xu, J. Tang, F.F. Wang, and Z.Q. Han, Development of squeeze casting technology for manufacturing aluminum alloy subframe for automobile, Foundry, 64(2015), No. 1, p. 17.
[2]	J.H. Park, K.J. Kim, J.W. Lee, and J.K. Yoon, Light-weight design of automotive suspension link based on design of experiment, Int. J. Automot. Technol., 16(2015), No. 1, p. 67.
[3]	X.H. Ao, S.M Xing, B.S. Yu, and Q.Y. Han, Effect of Ce addition on microstructures and mechanical properties of A380 aluminum alloy prepared by squeeze-casting, Int. J. Miner. Metall. Mater., 25(2018), No. 5, p. 553.
[4]	M.H. Farshidi, M. Rifai, and H. Miyamoto, Microstructure evolution of a recycled Al-Fe-Si-Cu alloy processed by tube channel pressing, Int. J. Miner. Metall. Mater., 25(2018), No. 10, p. 1166.
[5]	F.S. Pan and D.F. Zhang, Aluminum Alloy and Application, Chemical Industry Press, Beijing, 2006, p. 306.
[6]	X.C. Li, Microstructure and Metallographic Map of Aluminum Alloy Materials, Metallurgical Industry Press, Beijing, 2010, p. 1639.
[7]	Q. Zhao and S.X. Wang, Selection and Design of Aluminum Alloys, Chemical Industry Press, Beijing, 2017, p. 20.
[8]	X.M. Wang, Engineering Materials Science, Harbin Institute of Technology Press, Harbin, 2012, p. 148.
[9]	H. Mraied and W. Cai, The effects of Mn concentration on the tribocorrosion resistance of Al-Mn alloys, Wear, 380-381(2017), p. 191.
[10]	X.P. Chen, X.G. Li, S. Li, and Q. Liu, Continuous recrystallization of commercial Al-1.2wt%Mn alloy produced by thermomechanical processing, Mater. Lett., 180(2016), p. 101.
[11]	Z. Li, Z. Zhang, and X.G. Chen, Effect of magnesium on dispersoid strengthening of Al-Mn-Mg-Si (3xxx) alloys, Trans. Nonferrous Met. Soc. China, 26(2016), No. 11, p. 2793.
[12]	M. Sugamata, J. Kaneko, and N. Kimura, Structure and properties of rapidly solidified P/M samples of Al-Mn-Cr alloys, Mater. Sci. Forum, 416-418(2003), p. 359.
[13]	F.G. Coury, C.S. Kiminami, W.J. Botta, C. Bolfarini, and M. Kaufman, Design and production of Al-Mn-Ce alloys with tailored properties, Mater. Des., 110(2016), p. 436.
[14]	A. Kula, L. Blaz, and P. Lobry, Structure and properties studies of rapidly solidified Al-Mn alloys, Key Eng. Mater., 682(2016), p. 199.
[15]	D.W. Luo, J. Guo, Z.M. Yan, and T.J. Li, Effect of high magnetic fields on the solidification microstructure of an Al-Mn alloy, Rare Met., 28(2009), No. 3, p. 302.
[16]	Y.B. Dong, Y. Liu, and H. Lin, Leaching behavior of V, Pb, Cd, Cr, and As from stone coal waste rock with different particle sizes, Int. J. Miner. Metall. Mater., 25(2018), No. 8, p. 861.
[17]	C. Lin, S.S. Wu, S.L. Lü, P. An, and H.B. Wu, Effects of high-pressure rheo-squeeze casting on the Fe-rich phases and mechanical properties of Al-17Si-(1,1.5)Fe alloys, Int. J. Miner. Metall. Mater., 25(2018), No. 9, p. 1018.
[18]	K. Liu and X.G. Chen. Evolution of microstructure and elevated-temperature properties with Mn addition in Al-Mn-Mg alloys, J. Mater. Res., 32(2017), No. 13, p. 1.
[19]	L. Zhen, Z. Zhan, and X.G. Chen, Improvement in the mechanical properties and creep resistance of Al-Mn-Mg 3004 alloy with Sc and Zr addition, Mater. Sci. Eng. A, 729(2018), p. 196.
[20]	F.G. Coury, E.L. Pires, W. Wolf, F.H.P. de Almeida, A.L.C. e Silva, W.J. Botta, C.S. Kiminami, and M.J. Kaufman, Insight into the complex ternary phase behavior in Al-Mn-Ce alloys, J. Alloys Compd., 727(2017), p. 460.
[21]	S.L. Cui and I.H. Jung, Thermodynamic modeling of the Al-Cr-Mn ternary system, Metall. Mater. Trans. A, 48(2017), No. 3, p. 1383.
[22]	C.Q. Huang, J.X. Liu, and X.D. Jia, Effect of thermal deformation parameters on the microstructure, texture, and microhardness of 5754 aluminum alloy, Int. J. Miner. Metall. Mater., 26(2019), No. 9, p. 1140.
[23]	H.J. Kang, J.L. Li, T.M. Wang, and J.J. Guo, Growth behavior of primary intermetallic phases and mechanical properties for directionally solidified Al-Mn-Be alloy, Acta Metall. Sin., 54(2018), No. 5, p. 809.
[24]	X.C. Liu, Y. Pan, Z.J. Tang, W.Q. He, and T. Lu, Microstructure control and high temperature properties of Al-Mn-based alloys, Acta Metall. Sin., 53(2017), No. 11, p. 1487.
[25]	V. Raghavan, Al-Mn-Ni-Ti (Aluminum-Manganese-Nickel-Titanium), J. Phase Equilib. Diffus., 26(2005), No. 3, p. 280.
[26]	L. Ping and G.L. Dunlop, Microstructural characterization of rapidly solidified Al-Mn-Cr alloys, Mater. Sci. Eng. A, 134(1991), p. 1182.
[27]	H.A. Razazi, M. Paidar, and O.O. Ojo, Effect of Mn and Cr on structure and mechanical properties of Al-10%Mg-0.1%Ti alloy, Vacuum, 155(2018), p. 619.
[28]	G.X. Hu, X. Cai, and Y.H. Rong, Fundamentals of Materials Science, Shanghai Jiao Tong University Press, Shanghai, 2010, p. 231.
[29]	Y.D. He and X.M. Zhang, Refinement mechanism of trace Cr, Mn, Ti and Zr as cast 7A55 alloys, Chin. J. Nonferrous Met., 15(2005), No. 10, p. 1594.
[30]	Y. Birol, Effect of Cr and Zr on the grain structure of extruded EN AW 6082 alloy, Met. Mater. Int., 20(2014), No. 4, p. 727.
[31]	H.Q. Hu, Principle of Metal Solidification, Mechanical Industry Press, Beijing, 2017, p. 173.
[32]	Y. Zhang, W.B. Du, S.B. Li, K. Liu, C.H. Wang, and X.B. Zheng, Effect of cooling rate on solidification structure of Mg-8Gd-1Er alloy, Rare Met. Mater. Eng., 47(2018), No. 10, p. 3120.

Relative Articles

Cited By

Proportional views

数据统计

姓名
邮箱
手机号码
标题
留言内容
验证码

留言板

数据统计

分享

计量

Effect of Cr content and cooling rate on the primary phase of Al-2.5Mn alloy

中文摘要

Effect of Cr content and cooling rate on the primary phase of Al-2.5Mn alloy

Abstract

References

数据统计

Catalog