不同转速下预热辅助搅拌摩擦固态修复Al–Mg–Si合金板材

汪辉; 李一迪; 张明; 龚玮; 赖瑞林; 李云平

doi:10.1007/s12613-023-2772-9

Volume 31 Issue 4

Apr. 2024

Turn off MathJax

图(17) / 表(1)

数据统计

计量

文章访问数: 364
HTML全文浏览量: 147
PDF下载量: 49
被引次数: 0

文章导航 > 矿物冶金与材料学报（英文） > 2024 > 31(4): 725-736

Hui Wang, Yidi Li, Ming Zhang, Wei Gong, Ruilin Lai, and Yunping Li, Preheating-assisted solid-state friction stir repair of Al–Mg–Si alloy plate at different rotational speeds, Int. J. Miner. Metall. Mater., 31(2024), No. 4, pp. 725-736. https://doi.org/10.1007/s12613-023-2772-9

Cite this article as:

Hui Wang, Yidi Li, Ming Zhang, Wei Gong, Ruilin Lai, and Yunping Li, Preheating-assisted solid-state friction stir repair of Al–Mg–Si alloy plate at different rotational speeds, Int. J. Miner. Metall. Mater., 31(2024), No. 4, pp. 725-736. https://doi.org/10.1007/s12613-023-2772-9

Citation:

PDF( 10289 KB)

引用本文 PDF XML SpringerLink

研究论文

不同转速下预热辅助搅拌摩擦固态修复Al–Mg–Si合金板材

1)
粉末冶金国家重点实验室, 中南大学, 长沙 410083, 中国
2)
轻合金研究院, 中南大学, 长沙 410083, 中国

通讯作者:
赖瑞林 E-mail: lyping@csu.edu.cn

李云平 E-mail: lairuilin@csu.edu.cn

文章亮点

(1) 将基板预热应用于修复实验中，明显提高了修复质量。

(2) 系统地研究了刀具转速对Al–Mg–Si合金板材修复质量的影响规律，

(3) 为搅拌摩擦增材制造技术提供了很好地应用前景。

中文摘要

搅拌摩擦增材制造（Additive friction stir deposition，AFSD）作为一种新型结构修复和增材制造技术成为了近年来国内外的研究热点。在这项工作中，首次将基板预热应用到修复实验中，研究了预热辅助 AFSD 工艺修复的Al – Mg – Si合金板材的微观结构演变和力学性能。为了评估工具旋转速度和基板预热对修复质量的影响，我们使用 AFSD 技术对 Al – Mg – Si基板上 5 mm深度的盲孔进行了修复实验。结果表明，与未预热基材的对照条件相比，预热辅助 AFSD 修复可显著提高界面处的冶金结合和接头强度。此外，提高刀具旋转速度也有利于改善界面的冶金结合，避免出现体积缺陷。在基板预热条件下，修复后接头的力学性能与旋转速度呈正相关。在刀具转速为400–800 r/min的工艺参数下，修复试样界面均发现弱结合、空洞等缺陷，拉伸样品断裂在修复区。而转速为 1000 r/min时，可获得无缺陷试样，同时拉伸样品断裂在非修复区。UTS 和伸长率达到最大值 164.2 MPa 和 13.4%。

关键词:

Research Article

Preheating-assisted solid-state friction stir repair of Al–Mg–Si alloy plate at different rotational speeds

+ Author Affiliations

Abstract

Abstract

Additive friction stir deposition (AFSD) is a novel structural repair and manufacturing technology has become a research hotspot at home and abroad in the past five years. In this work, the microstructural evolution and mechanical performance of the Al–Mg–Si alloy plate repaired by the preheating-assisted AFSD process were investigated. To evaluate the tool rotation speed and substrate preheating for repair quality, the AFSD technique was used to additively repair 5 mm depth blind holes on 6061 aluminum alloy substrates. The results showed that preheat-assisted AFSD repair significantly improved joint bonding and joint strength compared to the control non-preheat substrate condition. Moreover, increasing rotation speed was also beneficial to improve the metallurgical bonding of the interface and avoid volume defects. Under preheating conditions, the UTS and elongation were positively correlated with rotation speed. Under the process parameters of preheated substrate and tool rotation speed of 1000 r/min, defect-free specimens could be obtained accompanied by tensile fracture occurring in the substrate rather than the repaired zone. The UTS and elongation reached the maximum values of 164.2 MPa and 13.4%, which are equivalent to 99.4% and 140% of the heated substrate, respectively.
- additive friction stir deposition;
- structural repair;
- tool rotation speed;
- Al alloy

FullText(HTML)

Supplements(0)

References(60)

References

[1]	A. Navabi, M. Vandadi, T. Bond, et al., Deformation and cracking phenomena in cold sprayed 6061 Al alloy powders with nanoscale aluminum oxide films, Mater. Sci. Eng. A, 841(2022), art. No. 143036. doi: 10.1016/j.msea.2022.143036
[2]	T. Wang, Y. Zou, X.M. Liu, and K. Matsuda, Special grain boundaries in the nugget zone of friction stir welded AA6061-T6 under various welding parameters, Mater. Sci. Eng. A, 671(2016), p. 7. doi: 10.1016/j.msea.2016.06.050
[3]	G.Y. Li, W.M. Jiang, F. Guan, et al., mechanical properties and corrosion resistance of A356 aluminum/AZ91D magnesium bimetal prepared by a compound casting combined with a novel Ni–Cu composite interlayer, J. Mater. Process. Technol., 288(2021), art. No. 116874. doi: 10.1016/j.jmatprotec.2020.116874
[4]	G.Y. Li, W.M. Jiang, F. Guan, J.W. Zhu, Y. Yu, and Z.T. Fan, Microstructure evolution, mechanical properties and fracture behavior of Al–xSi/AZ91D bimetallic composites prepared by a compound casting, J. Magnesium Alloys, (2022). DOI: 10.1016/j.jma.2022.08.010
[5]	J.C. Williams and E.A. Starke Jr, Progress in structural materials for aerospace systems1, Acta Mater., 51(2003), No. 19, p. 5775. doi: 10.1016/j.actamat.2003.08.023
[6]	W.F. Xu, Y.X. Luo, W. Zhang, and M.W. Fu, Comparative study on local and global mechanical properties of bobbin tool and conventional friction stir welded 7085-T7452 aluminum thick plate, J. Mater. Sci. Technol., 34(2018), No. 1, p. 173. doi: 10.1016/j.jmst.2017.05.015
[7]	J.L. Zhang, B. Song, Q.S. Wei, D. Bourell, and Y.S. Shi, A review of selective laser melting of aluminum alloys: Processing, microstructure, property and developing trends, J. Mater. Sci. Technol., 35(2019), No. 2, p. 270. doi: 10.1016/j.jmst.2018.09.004
[8]	A. Abdollahzadeh, B. Bagheri, A.H. Vaneghi, A. Shamsipur, and S.E. Mirsalehi, Advances in simulation and experimental study on intermetallic formation and thermomechanical evolution of Al–Cu composite with Zn interlayer: Effect of spot pass and shoulder diameter during the pinless friction stir spot welding process, Proc. Inst. Mech. Eng., Part L: J. Mater.: Des. Appl., 237(2022), No. 6, p. 1475. doi: 10.1177/14644207221146981
[9]	J.B. Wang, J. Zhang, Y. Zhang, F. Xie, S. Krajnovic, and G.J. Gao, Impact of bogie cavity shapes and operational environment on snow accumulating on the bogies of high-speed trains, J. Wind Eng. Ind. Aerodyn., 176(2018), p. 211. doi: 10.1016/j.jweia.2018.03.027
[10]	X.Y. Wu, Z.Y. Zhang, W.C. Qi, R.Y. Tian, S.M. Huang, and C.Y. Shi, Corrosion behavior of SMA490BW steel and welded joints for high-speed trains in atmospheric environments, Materials, 12(2019), No. 18, art. No. 3043. doi: 10.3390/ma12183043
[11]	Q. Zhu, H. Yu, J.Q. Zhang, M. Li, and X.G. Hu, Experimental study on Tig welding properties of 6061 and 7003 aluminum alloys, [in] Proceedings of the 2020 5th International Conference on Renewable Energy and Environmental Protection, Shenzhen, 2020.
[12]	T.H. Naing and P. Muangjunburee, Metallurgical and mechanical characterization of MIG welded repair joints for 6082-T6 aluminum alloy with ER 4043 and ER 5356, Trans. Indian Inst. Met., 75(2022), No. 6, p. 1583. doi: 10.1007/s12666-022-02523-7
[13]	R.J. Griffiths, M.E.J. Perry, J.M. Sietins, et al. , A perspective on solid-state additive manufacturing of aluminum matrix composites using MELD, J. Mater. Eng. Perform., 28(2019), No. 2, p. 648. doi: 10.1007/s11665-018-3649-3
[14]	W.D. Hartley, D. Garcia, J.K. Yoder, et al., Solid-state cladding on thin automotive sheet metals enabled by additive friction stir deposition, J. Mater. Process. Technol., 291(2021), art. No. 117045. doi: 10.1016/j.jmatprotec.2021.117045
[15]	H.Z. Yu, M.E. Jones, G.W. Brady, et al., Non-beam-based metal additive manufacturing enabled by additive friction stir deposition, Scripta Mater., 153(2018), p. 122. doi: 10.1016/j.scriptamat.2018.03.025
[16]	D. Garcia, W.D. Hartley, H.A. Rauch, et al., In situ investigation into temperature evolution and heat generation during additive friction stir deposition: A comparative study of Cu and Al–Mg–Si, Addit. Manuf., 34(2020), art. No. 101386. doi: 10.1016/j.addma.2020.101386
[17]	Y.D. Li, B.B. Yang, M. Zhang, et al., The corrosion behavior and mechanical properties of 5083 Al–Mg alloy manufactured by additive friction stir deposition, Corros. Sci., 213(2023), art. No. 110972. doi: 10.1016/j.corsci.2023.110972
[18]	P. Agrawal, R.S. Haridas, S. Yadav, et al., Processing-structure-property correlation in additive friction stir deposited Ti–6Al–4V alloy from recycled metal chips, Addit. Manuf., 47(2021), art. No. 102259. doi: 10.1016/j.addma.2021.102259
[19]	C.J.T. Mason, R.I. Rodriguez, D.Z. Avery, et al., Process-structure-property relations for as-deposited solid-state additively manufactured high-strength aluminum alloy, Addit. Manuf., 40(2021), art. No. 101879. doi: 10.1016/j.addma.2021.101879
[20]	F. Khodabakhshi and A.P. Gerlich, Potentials and strategies of solid-state additive friction-stir manufacturing technology: A critical review, J. Manuf. Processes, 36(2018), p. 77. doi: 10.1016/j.jmapro.2018.09.030
[21]	C.Y. Zeng, H. Ghadimi, H. Ding, et al., Microstructure evolution of Al6061 alloy made by additive friction stir deposition, Materials, 15(2022), No. 10, art. No. 3676. doi: 10.3390/ma15103676
[22]	B.J. Phillips, C.J. Williamson, R.P. Kinser, J.B. Jordon, K.J. Doherty, and P.G. Allison, Microstructural and mechanical characterization of additive friction stir-deposition of aluminum alloy 5083 effect of lubrication on material anisotropy, Materials, 14(2021), No. 21, art. No. 6732. doi: 10.3390/ma14216732
[23]	G.R. Merritt, M.B. Williams, P.G. Allison, J.B. Jordon, T.W. Rushing, and C.A. Cousin, Closed-loop temperature and force control of additive friction stir deposition, J. Manuf. Mater. Process., 6(2022), No. 5, art. No. 92. doi: 10.3390/jmmp6050092
[24]	K. Anderson-Wedge, D.Z. Avery, S.R. Daniewicz, et al., Characterization of the fatigue behavior of additive friction stir-deposition AA2219, Int. J. Fatigue, 142(2021), art. No. 105951. doi: 10.1016/j.ijfatigue.2020.105951
[25]	O.G. Rivera, P.G. Allison, L.N. Brewer, et al., Influence of texture and grain refinement on the mechanical behavior of AA2219 fabricated by high shear solid state material deposition, Mater. Sci. Eng. A, 724(2018), p. 547. doi: 10.1016/j.msea.2018.03.088
[26]	Y.D. Li, M. Zhang, H. Wang, R.L. Lai, B.B. Yang, and Y.P. Li, Microstructure and mechanical properties of Al–Li alloy manufactured by additive friction stir deposition, Mater. Sci. Eng. A, 887(2023), art. No. 145753. doi: 10.1016/j.msea.2023.145753
[27]	W.S. Tang, X.Q. Yang, C.B. Tian, and C. Gu, Effect of rotation speed on microstructure and mechanical anisotropy of Al-5083 alloy builds fabricated by friction extrusion additive manufacturing, Mater. Sci. Eng. A, 860(2022), art. No. 144237. doi: 10.1016/j.msea.2022.144237
[28]	Z.K. Shen, M.T. Zhang, D.X. Li, et al., Microstructural characterization and mechanical properties of AlMg alloy fabricated by additive friction stir deposition, Int. J. Adv. Manuf. Technol., 125(2023), No. 5-6, p. 2733. doi: 10.1007/s00170-023-10952-x
[29]	W.S. Tang, X.Q. Yang, C.B. Tian, and Y.S. Xu, Interfacial grain structure, texture and tensile behavior of multilayer deformation-based additively manufactured Al 6061 alloy, Mater. Charact., 196(2023), art. No. 112646. doi: 10.1016/j.matchar.2023.112646
[30]	F.C. Liu, P.S. Dong, A.S. Khan, et al., 3D printing of fine-grained aluminum alloys through extrusion-based additive manufacturing: Microstructure and property characterization, J. Mater. Sci. Technol., 139(2023), p. 126. doi: 10.1016/j.jmst.2022.08.017
[31]	W.S. Tang, X.Q. Yang, and C.B. Tian, Influence of rotation speed on interfacial bonding mechanism and mechanical performance of aluminum 6061 fabricated by multilayer friction-based additive manufacturing, Int. J. Adv. Manuf. Technol., 126(2023), No. 9-10, p. 4119. doi: 10.1007/s00170-023-11378-1
[32]	W. Gong, Y.D. Li, M. Zhang, et al., Influence of preheating temperature on the microstructure and mechanical properties of 6061/TA1 composite plates fabricated by AFSD, Materials, 16(2023), No. 17, art. No. 6018. doi: 10.3390/ma16176018
[33]	J.K. Yoder, R.J. Griffiths, and H.Z. Yu, Deformation-based additive manufacturing of 7075 aluminum with wrought-like mechanical properties, Mater. Des., 198(2021), art. No. 109288. doi: 10.1016/j.matdes.2020.109288
[34]	V. Gopan, K. Leo Dev Wins, and A. Surendran, Innovative potential of additive friction stir deposition among current laser based metal additive manufacturing processes: A review, CIRP J. Manuf. Sci. Technol., 32(2021), p. 228. doi: 10.1016/j.cirpj.2020.12.004
[35]	S.S. Joshi, S.M. Patil, S. Mazumder, et al., Additive friction stir deposition of AZ31B magnesium alloy, J. Magnesium Alloys, 10(2022), No. 9, p. 2404. doi: 10.1016/j.jma.2022.03.011
[36]	S. Sharma, K.V.M. Krishna, M. Radhakrishnan, et al., A pseudo thermo-mechanical model linking process parameters to microstructural evolution in multilayer additive friction stir deposition of magnesium alloy, Mater. Des., 224(2022), art. No. 111412. doi: 10.1016/j.matdes.2022.111412
[37]	J.L. Priedeman, B.J. Phillips, J.J. Lopez, et al., Microstructure development in additive friction stir-deposited Cu, Metals, 10(2020), No. 11, art. No. 1538. doi: 10.3390/met10111538
[38]	O. Rivera, P. Allison, J.B. Jordon, et al., Microstructures and mechanical behavior of Inconel 625 fabricated by solid-state additive manufacturing, Mater. Sci. Eng. A, 694(2017), p. 1. doi: 10.1016/j.msea.2017.03.105
[39]	P. Agrawal, R.S. Haridas, S. Yadav, S. Thapliyal, A. Dhal, and R.S. Mishra, Additive friction stir deposition of SS316: Effect of process parameters on microstructure evolution, Mater. Charact., 195(2023), art. No. 112470. doi: 10.1016/j.matchar.2022.112470
[40]	R.J. Griffiths, D.T. Petersen, D. Garcia, and H.Z. Yu, Additive friction stir-enabled solid-state additive manufacturing for the repair of 7075 aluminum alloy, Appl. Sci., 9(2019), No. 17, p. 3486. doi: 10.3390/app9173486
[41]	D.Z. Avery, C.E. Cleek, B.J. Phillips, et al., Evaluation of microstructure and mechanical properties of Al–Zn–Mg–Cu alloy repaired via additive friction stir deposition, J. Eng. Mater. Technol., 144(2022), No. 3, art. No. 031003. doi: 10.1115/1.4052816
[42]	L.P. Martin, A. Luccitti, and M. Walluk, Repair of aluminum 6061 plate by additive friction stir deposition, Int. J. Adv. Manuf. Technol., 118(2022), No. 3-4, p. 759 doi: 10.1007/s00170-021-07953-z
[43]	Y.J. Li, W.Z. Zhang, and K. Marthinsen, Precipitation crystallography of plate-shaped Al₆(Mn,Fe) dispersoids in AA5182 alloy, Acta Mater., 60(2012), No.17, p. 5963. doi: 10.1016/j.actamat.2012.06.022
[44]	Z.P. Que, Y. Wang, Z.Y. Fan, T. Hashimoto, and X.R. Zhou, Enhanced heterogeneous nucleation of Al₆(Fe,Mn) compound in Al alloys by interfacial segregation of Mn on TiB₂ particles surface, Mater. Lett., 323(2022), p. art. No. 132570. doi: 10.1016/j.matlet.2022.132570
[45]	F.J. Humphreys, Quantitative metallography by electron backscattered diffraction, J. Microsc., 195(1999), p. 170. doi: 10.1046/j.1365-2818.1999.00578.x
[46]	M.E.J. Perry, R.J. Griffiths, D. Garcia, J.M. Sietins, Y. Zhu, and H.Z. Yu, Morphological and microstructural investigation of the non-planar interface formed in solid-state metal additive manufacturing by additive friction stir deposition, Addit. Manuf., 35(2020), art. No. 101293. doi: 10.1016/j.addma.2020.101293
[47]	R.J. Griffiths, D. Garcia, J. Song, et al., Solid-state additive manufacturing of aluminum and copper using additive friction stir deposition: Process-microstructure linkages, Materialia, 15(2021), p. 82. doi: 10.3390/ma15010082
[48]	S. Beck, B.A. Rutherford, D.Z. Avery, et al., The effect of solutionizing and artificial aging on the microstructure and mechanical properties in solid-state additive manufacturing of precipitation hardened Al–Mg–Si alloy, Mater. Sci. Eng. A, 819(2021), art. No. 141351. doi: 10.1016/j.msea.2021.141351
[49]	B.J. Phillips, D.Z. Avery, T. Liu, et al., Microstructure-deformation relationship of additive friction stir-deposition Al–Mg–Si, Materialia, 7(2019), art. No. 100387. doi: 10.1016/j.mtla.2019.100387
[50]	W.S. Tang, X.Q. Yang, C.B. Tian, and Y.S. Xu, Microstructural heterogeneity and bonding strength of planar interface formed in additive manufacturing of Al–Mg–Si alloy based on friction and extrusion, Int. J. Miner. Metall. Mater., 29(2022), No. 9, p. 1755. doi: 10.1007/s12613-022-2506-4
[51]	H.S. Kim, Y. Estrin, and M.B. Bush, Plastic deformation behaviour of fine-grained materials, Acta Mater., 48(2000), No.2, p. 493. doi: 10.1016/S1359-6454(99)00353-5
[52]	C.X. Zhu, X.H. Tang, Y. He, F.G. Lu, and H.C. Cui, Effect of preheating on the defects and microstructure in NG-GMA welding of 5083 Al-alloy, J. Mater. Process. Technol., 251(2018), p. 214. doi: 10.1016/j.jmatprotec.2017.08.037
[53]	M. Jawad, M. Jahanzaib, M.A. Ali, et al., Revealing the microstructure and mechanical attributes of pre-heated conditions for gas tungsten arc welded AISI 1045 steel joints, Int. J. Press. Vessels Pip., 192(2021), art. No. 104440. doi: 10.1016/j.ijpvp.2021.104440
[54]	V.S. Gadakh and K. Adepu, Heat generation model for taper cylindrical pin profile in FSW, J. Mater. Res. Technol., 2(2013), No.4, p. 370. doi: 10.1016/j.jmrt.2013.10.003
[55]	A. Barbini, J. Carstensen, and J.F. dos Santos, Influence of a non-rotating shoulder on heat generation, microstructure and mechanical properties of dissimilar AA2024/AA7050 FSW joints, J. Mater. Sci. Technol., 34(2018), No. 1, p. 119. doi: 10.1016/j.jmst.2017.10.017
[56]	M. Maalekian, E. Kozeschnik, H.P. Brantner, and H. Cerjak, Comparative analysis of heat generation in friction welding of steel bars, Acta Mater., 56(2008), No.12, p. 2843. doi: 10.1016/j.actamat.2008.02.016
[57]	Z.K. Zhang, X.B. Li, Z.L. Zhao, C.M. Jiang, and H.X. Zhao, Process optimization and formation analysis of friction plug welding of 6082 aluminum alloy, Metals, 10(2020), No.11, art. No. 1454. doi: 10.3390/met10111454
[58]	S.D. Ji, X.C. Meng, R.F. Huang, L. Ma, and S.S. Gao, Microstructures and mechanical properties of 7N01-T4 aluminum alloy joints by active-passive filling friction stir repairing, Mater. Sci. Eng. A, 664(2016), p. 94. doi: 10.1016/j.msea.2016.03.131
[59]	L.P. Martin, A. Luccitti, and M. Walluk, Evaluation of additive friction stir deposition for the repair of cast Al–1.4Si–1.1Cu–1.5Mg–2.1Zn, J. Manuf. Sci. Eng., 144(2022), No. 6, art. No. 061006. doi: 10.1115/1.4052759
[60]	Z.Y. Zhang, X.G. Sun, S.M. Huang, et al., Microstructure, mechanical properties and corrosion behavior of the aluminum alloy components repaired by cold spray with Al-based powders, Metals, 11(2021), No. 10, art. No. 1633. doi: 10.3390/met11101633