Fabrication and compressive performance of plain carbon steel honeycomb sandwich panels

Yu'an Jing, Shiju Guo, Jingtao Han, Yufei Zhang, Weijuan Li

分享

计量
  • 文章访问数:  273
  • HTML全文浏览量:  80
  • PDF下载量:  16
  • 被引次数: 0

目录

    Cite this article as:

    Yu'an Jing, Shiju Guo, Jingtao Han, Yufei Zhang, and Weijuan Li, Fabrication and compressive performance of plain carbon steel honeycomb sandwich panels, J. Univ. Sci. Technol. Beijing , 15(2008), No. 3, pp.255-260. https://dx.doi.org/10.1016/S1005-8850(08)60048-1
    Yu'an Jing, Shiju Guo, Jingtao Han, Yufei Zhang, and Weijuan Li, Fabrication and compressive performance of plain carbon steel honeycomb sandwich panels, J. Univ. Sci. Technol. Beijing , 15(2008), No. 3, pp.255-260. https://dx.doi.org/10.1016/S1005-8850(08)60048-1
    引用本文 PDF XML SpringerLink
    Materials

    Fabrication and compressive performance of plain carbon steel honeycomb sandwich panels

      通信作者:

      Yu'an Jing E-mail: jyachina@163.com

    Plain carbon steel Q215 honeycomb sandwich panels were manufactured by brazing in a vacuum furnace. Their characteristic parameters, including equivalent density, equivalent elastic modulus, and equivalent compressive strength along out-of-plane (z-direction) and in-plane (x-and y-directions), were derived theoretically and then determined experimentally by an 810 material test system. On the basis of the experimental data, the compressive stress-strain curves were given. The results indicate that the measurements of equivalent Young's modulus and initial compressive strength are in good agreement with calculations, and that the maximum compressive strain near to solid can be up to 0.5-0.6 along out-of-plane, 0.6-0.7 along in-plane. The strength-to-density ratio of plain carbon steel honeycomb panels is near to those of Al alloy hexagonal-honeycomb and 304L stainless steel square-honeycomb, but the compressive peak strength is greater than that of Al alloy hexagonal-honeycomb.

     

    Materials

    Fabrication and compressive performance of plain carbon steel honeycomb sandwich panels

    Author Affilications
    • Received: 23 June 2007;
    Plain carbon steel Q215 honeycomb sandwich panels were manufactured by brazing in a vacuum furnace. Their characteristic parameters, including equivalent density, equivalent elastic modulus, and equivalent compressive strength along out-of-plane (z-direction) and in-plane (x-and y-directions), were derived theoretically and then determined experimentally by an 810 material test system. On the basis of the experimental data, the compressive stress-strain curves were given. The results indicate that the measurements of equivalent Young's modulus and initial compressive strength are in good agreement with calculations, and that the maximum compressive strain near to solid can be up to 0.5-0.6 along out-of-plane, 0.6-0.7 along in-plane. The strength-to-density ratio of plain carbon steel honeycomb panels is near to those of Al alloy hexagonal-honeycomb and 304L stainless steel square-honeycomb, but the compressive peak strength is greater than that of Al alloy hexagonal-honeycomb.

     

    Relative Articles

    Ali Arab, Roslan Ahmad, Zainal Arifin Ahmad. Effect of SrCO3 addition on the dynamic compressive strength of ZTA [J]. 矿物冶金与材料学报(英文版). DOI: 10.1007/s12613-016-1259-3

    View details

    Xin-hua Liu, Hai-you Huang, Jian-xin Xie. Effect of strain rate on the compressive deformation behaviors of lotus-type porous copper [J]. 矿物冶金与材料学报(英文版). DOI: 10.1007/s12613-014-0959-9

    View details

    Int. J. Miner. Metall. Mater., 2014, 21(5): 431-437.

    PDF View details

    Feng-man Shen, Qiang-jian Gao, Xin Jiang, Guo Wei, Hai-yan Zheng. Effect of magnesia on the compressive strength of pellets [J]. 矿物冶金与材料学报(英文版). DOI: 10.1007/s12613-014-0926-5

    View details

    Int. J. Miner. Metall. Mater., 2014, 21(4): 339-344.

    PDF View details

    Jian-liang Zhang, Zhen-yang Wang, Xiang-dong Xing, Zheng-jian Liu. Effect of aluminum oxide on the compressive strength of pellets [J]. 矿物冶金与材料学报(英文版). DOI: 10.1007/s12613-014-0914-9

    View details

    Chai Jaturapitakkul, Jatuphon Tangpagasit, Sawang Songmue, Kraiwood Kiattikomol. Filler effect of fine particle sand on the compressive strength of mortar [J]. 矿物冶金与材料学报(英文版). DOI: 10.1007/s12613-011-0429-6

    View details

    P. Chindaprasirt, S. Hatanaka, N. Mishima, Y. Yuasa, T. Chareerat. Effects of binder strength and aggregate size on the compressive strength and void ratio of porous concrete [J]. 矿物冶金与材料学报(英文版). DOI: 10.1016/S1674-4799(10)60018-0

    View details

    Daohui Xiang, Ming Chen, Yuping Ma, Fanghong Sun. Adhesive strength of CVD diamond thin films quantitatively measured by means of the bulge and blister test [J]. 矿物冶金与材料学报(英文版). DOI: 10.1016/S1005-8850(08)60089-4

    View details

    Yumin Liu, Zhongyuan Yu, Yongzhen Huang. Dependence of elastic strain field on the self-organized ordering of quantum dot superlattices [J]. 矿物冶金与材料学报(英文版). DOI: 10.1016/S1005-8850(07)60094-2

    View details

    Di Tang, Qingwu Cai, Yueqin Li, Yumei Pu, Yuzhou Zhu. Recrystallization of High Carbon Steel during High Strain Rate [J]. 矿物冶金与材料学报(英文版).

    View details

    /

    返回文章
    返回