Effect of Cu addition on the microstructure and tribological performance of Ni60 directional structure coating

Xiaotian Yang; Xinhua Wang; Jun Zhou; Hengli Wei; Rong Zeng; Wensheng Li

doi:10.1007/s12613-022-2516-2

Volume 30 Issue 4

Apr. 2023

Turn off MathJax

Article Contents

Article Navigation > International Journal of Minerals, Metallurgy and Materials > 2023 > 30(4): 715-723

Xiaotian Yang, Xinhua Wang, Jun Zhou, Hengli Wei, Rong Zeng, and Wensheng Li, Effect of Cu addition on the microstructure and tribological performance of Ni60 directional structure coating, Int. J. Miner. Metall. Mater., 30(2023), No. 4, pp. 715-723. https://doi.org/10.1007/s12613-022-2516-2

Cite this article as:

Xiaotian Yang, Xinhua Wang, Jun Zhou, Hengli Wei, Rong Zeng, and Wensheng Li, Effect of Cu addition on the microstructure and tribological performance of Ni60 directional structure coating, Int. J. Miner. Metall. Mater., 30(2023), No. 4, pp. 715-723. https://doi.org/10.1007/s12613-022-2516-2

Citation:

PDF( 4391 KB)

Research Article

Effect of Cu addition on the microstructure and tribological performance of Ni60 directional structure coating

+ Author Affiliations

Corresponding author:
Xiaotian Yang E-mail: 398830990@qq.com
Received: 29 September 2021; Revised: 24 May 2022; Accepted: 25 May 2022; Available online: 28 May 2022

Abstract

Abstract

The Ni60/15wt% Cu directional structure coating was prepared by the composite technology of flame spraying, induction remelting, and forced cooling, and the effect of Cu on the microstructure, phase, hardness, and wear performance of Ni60 coatings was investigated. Results showed that Cu addition makes the microstructure of Ni60 directional structure coating more compact, and Cu is mainly enriched within the crystal grain, resulting in the formation of Cu_3.8Ni as the bonding phase. Compared with Ni60 directional structure coating, Ni60/Cu directional structure coating has a lower hardness, lower friction coefficient, and lower wear rate, which indicate that Cu can effectively enhance the antifriction performance of Ni60 directional structure coating.
- induction remelting;
- directional structure coating;
- microstructure;
- tribological performance

FullText(HTML)

Supplements(0)

References(47)

References

[1]	S.M. Muthu, M. Arivarasu, T.H. Krishna, S. Ganguly, K.V.P. Prabhakar, and S. Mohanty, Improvement in hot corrosion resistance of dissimilar alloy 825 and AISI 321 CO₂-laser weldment by HVOF coating in aggressive salt environment at 900°C, Int. J. Miner. Metall. Mater., 27(2020), No. 11, p. 1536. doi: 10.1007/s12613-020-2014-3
[2]	C. Navas, R. Colaço, J. de Damborenea, and R. Vilar, Abrasive wear behaviour of laser clad and flame sprayed-melted NiCrBSi coatings, Surf. Coat. Technol., 200(2006), No. 24, p. 6854. doi: 10.1016/j.surfcoat.2005.10.032
[3]	X.T. Yang, X.Q. Li, Q.B. Yang, H.L. Wei, X.Y. Fu, and W.S. Li, Effects of WC on microstructure and corrosion resistance of directional structure Ni60 coatings, Surf. Coat. Technol., 385(2020), art. No. 125359. doi: 10.1016/j.surfcoat.2020.125359
[4]	X.Y. Wang, S.F. Zhou, X.Q. Dai, et al., Evaluation and mechanisms on heat damage of WC particles in Ni60/WC composite coatings by laser induction hybrid cladding, Int. J. Refract. Met. Hard Mater., 64(2017), p. 234. doi: 10.1016/j.ijrmhm.2016.11.001
[5]	Z.H. Wen, Y. Bai, J.F. Yang, and J. Huang, Effect of vacuum re-melting on the solid particles erosion behavior of Ni60–NiCrMoY composite coatings prepared by plasma spraying, Vacuum, 134(2016), p. 73. doi: 10.1016/j.vacuum.2016.09.020
[6]	E. Rabinowicz and R.I. Tanner, Friction and wear of materials, J. Appl. Mech., 33(1995), No. 2, p. 479.
[7]	H.D.V. Mejía, D. Perea, and G.B. Gilberto, Development and characterization of TiAlN (Ag, Cu) nanocomposite coatings deposited by DC magnetron sputtering for tribological applications, Surf. Coat. Technol., 381(2020), art. No. 125095. doi: 10.1016/j.surfcoat.2019.125095
[8]	J.W. Zhang, Y.X. Wang, S.G. Zhou, et al., Tailoring self-lubricating, wear-resistance, anticorrosion and antifouling properties of Ti/(Cu, MoS₂)–DLC coating in marine environment by controlling the content of Cu dopant, Tribol. Int., 143(2020), art. No. 106029. doi: 10.1016/j.triboint.2019.106029
[9]	J.C. Ding, T.F. Zhang, Z.X. Wan, et al., Influence of Cu content on the microstructure and mechanical properties of Cr–Cu–N coatings, Scanning, 2018(2018), art. No. 6491279.
[10]	H.J. Zhao, F.F. Guo, L.Y. Zhu, J.N. He, and F.X. Yin, The effect of Cu addition on the crystallization behavior and tribological properties of reactive plasma sprayed TiCN–Cu coatings, Ceram. Int., 46(2020), No. 6, p. 8344. doi: 10.1016/j.ceramint.2019.12.066
[11]	H.J. Mei, R. Wang, X. Zhong, W. Dai, and Q.M. Wang, Influence of nitrogen partial pressure on microstructure and tribological properties of Mo–Cu–V–N composite coatings with high Cu content, Coatings, 8(2018), No. 1, art. No. 24. doi: 10.3390/coatings8010024
[12]	E.B. Moustafa and M.A. Taha, Evaluation of the microstructure, thermal and mechanical properties of Cu/SiC nanocomposites fabricated by mechanical alloying, Int. J. Miner. Metall. Mater., 28(2021), No. 3, p. 475. doi: 10.1007/s12613-020-2176-z
[13]	Z.T. Li, Y.X. Wu, B.S. Zhuang, et al., Preparation of novel copper-powder-sintered frame/paraffin form-stable phase change materials with extremely high thermal conductivity, Appl. Energy, 206(2017), p. 1147. doi: 10.1016/j.apenergy.2017.10.046
[14]	H.J. Mei, D.S. Geng, R. Wang, et al., Effect of Cu doping on the microstructure and mechanical properties of AlTiVN–Cu nanocomposite coatings, Surf. Coat. Technol., 402(2020), art. No. 126490. doi: 10.1016/j.surfcoat.2020.126490
[15]	Q.Z. Wang, Y.S. Ding, F. Zhou, and J.Z. Kong, Comparison of mechanical and tribological properties of Ni–CrSiN and Cu–CrSiN coatings via thermal-cold cycling treatment, Surf. Coat. Technol., 400(2020), art. No. 126232. doi: 10.1016/j.surfcoat.2020.126232
[16]	X. Xu, F.H. Su, and Z.J. Li, Microstructure and tribological behaviors of MoN–Cu nanocomposite coatings sliding against Si₃N₄ ball under dry and oil-lubricated conditions, Wear, 434-435(2019), art. No. 202994. doi: 10.1016/j.wear.2019.202994
[17]	V.A. Frolov, V.A. Poklad, B.V. Ryabenko, and D.V. Viktorenkov, Technological special features of methods of supersonic thermal spraying, Weld. Int., 21(2007), No. 4, p. 315. doi: 10.1080/09507110701412047
[18]	C.R. Si, B.B. Duan, Q. Zhang, J. Cai, and W.C. Wu, Microstructure, corrosion-resistance, and wear-resistance properties of subsonic flame sprayed amorphous Fe–Mo–Cr–Co coating with extremely high amorphous rate, J. Mater. Res. Technol., 9(2020), No. 3, p. 3292. doi: 10.1016/j.jmrt.2020.01.024
[19]	Z. Bergant and J. Grum, Quality improvement of flame sprayed, heat treated, and remelted NiCrBSi coatings, J. Therm. Spray Technol., 18(2009), No. 3, p. 380. doi: 10.1007/s11666-009-9304-7
[20]	J. Yu and H.F. Yu, Coating properties, energy consumption, and cost analysis of the induction cladding process, Results Phys., 17(2020), art. No. 103043. doi: 10.1016/j.rinp.2020.103043
[21]	J.B. Chen, Y.C. Dong, L.N. Wan, et al., Effect of induction remelting on the microstructure and properties of in situ TiN-reinforced NiCrBSi composite coatings, Surf. Coat. Technol., 340(2018), p. 159. doi: 10.1016/j.surfcoat.2018.02.024
[22]	T.S. Dong, L. Liu, G.L. Li, R. Wang, J.M. Yuan, and Y. Feng, Effect of induction remelting on microstructure and wear resistance of plasma sprayed NiCrBSiNb coatings, Surf. Coat. Technol., 364(2019), p. 347. doi: 10.1016/j.surfcoat.2019.02.083
[23]	H.L. Wang, Q. Wang, L.C. Zeng, H.L. Zhang, and H.S. Ding, Microstructure, mechanical and tribological performances of a directionally solidified γ-TiAl alloy, Mater. Charact., 179(2021), art. No. 111393. doi: 10.1016/j.matchar.2021.111393
[24]	X. Zhan, D. Wang, Z.C. Ge, et al., Microstructural evolution of NiCoCrAlY coated directionally solidified superalloy, Surf. Coat. Technol., 440(2022), art. No. 128487. doi: 10.1016/j.surfcoat.2022.128487
[25]	X.T. Yang, P.C. Wang, X. Li, Y. Lu, and R.Z. Xiao, Evolution characteristics of microstructure of Ni-based alloy coatings and their properties under complex process, Rare Met. Mater. Eng., 46(2017), No. 3, p. 693.
[26]	P.C. Wang, Y. Lu, X.T. Yang, R.Z. Xiao, and X.W. Yang, Effect of forced cooling on microstructure of induction remelting Ni60 alloy coating, Chin. J. Nonferrous Met., 26(2016), No. 2, p. 375.
[27]	J.N. Balaraju, C. Anandan, and K.S. Rajam, Influence of codeposition of copper on the structure and morphology of electroless Ni–W–P alloys from sulphate- and chloride-based baths, Surf. Coat. Technol., 200(2006), No. 12-13, p. 3675. doi: 10.1016/j.surfcoat.2004.09.010
[28]	Y.N. Cao, Y.Q. Xia, B.Y. Duan, W.X. Mu, X. Tan, and H. Wu, Microstructure evolution and anti-wear mechanism of Cu film fabricated by magnetron sputtering deposition, Mater. Lett., 315(2022), art. No. 131941. doi: 10.1016/j.matlet.2022.131941
[29]	H. Tan, Y.B. Guo, D.G. Wang, and Y.J. Cui, The development of a Cu@Graphite solid lubricant with excellent anti-friction and wear resistant performances in dry condition, Wear, 488-489(2022), art. No. 204181. doi: 10.1016/j.wear.2021.204181
[30]	T. Kalfhaus, H. Schaar, F. Thaler, et al., Path to single-crystalline repair and manufacture of Ni-based superalloy using directional annealing, Surf. Coat. Technol., 405(2021), art. No. 126494. doi: 10.1016/j.surfcoat.2020.126494
[31]	M.Z. Alam, D.V.V. Satyanarayana, D. Chatterjee, R. Sarkar, and D.K. Das, Creep behavior of Pt-aluminide (PtAl) coated directionally solidified Ni-based superalloy CM–247LC after thermal exposure, Mater. Sci. Eng. A, 641(2015), p. 84. doi: 10.1016/j.msea.2015.06.011
[32]	B.B. Yang, Y.H. Hou, Q. Lei, Y.P. Li, and A. Chiba, Influence of Cu addition on corrosion behavior and tensile performance of Ni–30Co–16Cr–15Mo–6Fe alloy, Mater. Charact., 161(2020), art. No. 110140. doi: 10.1016/j.matchar.2020.110140
[33]	H. Shi, J.H. Yang, and W.H. Lai, Influence of Cu addition on properties and microstructure of WC–13%Fe/Co/Ni cemented carbides, Powder Metall. Technol., 13(1995), No. 3, p. 174.
[34]	X.Z. Liu, Q.W. Shen, X.Z. Liu, J. Chen, L.W. Zhu, and J. Qi, Effect of heat treatment temperature on the spectral properties of Cu–Ni coating, Spectrosc. Spect. Anal., 35(2015), No. 4, p. 1094.
[35]	C. Cao, D.B. Chen, X.Y. Fang, et al., Effects of Cu addition on the microstructure and properties of the Al–Mn–Fe–Si alloy, J. Alloys Compd., 834(2020), art. No. 155175. doi: 10.1016/j.jallcom.2020.155175
[36]	L. Venkatesh, I. Samajdar, M. Tak, et al., Microstructure and phase evolution in laser clad chromium carbide–NiCrMoNb, Appl. Surf. Sci., 357(2015), p. 2391. doi: 10.1016/j.apsusc.2015.09.260
[37]	Y. Deo, S. Guha, K. Sarkar, P. Mohanta, D. Pradhan, and A. Mondal, Electrodeposited Ni–Cu alloy coatings on mild steel for enhanced corrosion properties, Appl. Surf. Sci., 515(2020), art. No. 146078. doi: 10.1016/j.apsusc.2020.146078
[38]	X.T. Yang, J.L. Duan, and X.Y. Fu, Directional crystal structure characteristics of Ni60/high-aluminum bronze composite coating, J. Harbin Eng. Univ., 39(2018), No. 12, p. 2068.
[39]	L.W. Xu, N. Lin, C. Ma, Z.Y. Wang, X.Y. Kang, and Y.H. He, Effect of Cu addition on the microstructures and properties of ultrafine Ti(C, N)-based cermet, Vacuum, 181(2020), art. No. 109753. doi: 10.1016/j.vacuum.2020.109753
[40]	X.T. Yang, X.Y. Fu, J.L. Duan, X.Q. Li, H.L. Wei, and W.S. Li, Microstructure and wear resistance of directionally solidified Ni60/aluminum bronze coating after spraying, Surf. Technol., 48(2019), No. 1, p. 182.
[41]	G. Liu, D. Du, K.M. Wang, Z. Pu, D.Q. Zhang, and B.H. Chang, Microstructure and wear behavior of IC10 directionally solidified superalloy repaired by directed energy deposition, J. Mater. Sci. Technol., 93(2021), p. 71. doi: 10.1016/j.jmst.2021.04.006
[42]	F. Bertelli, E.S. Freitas, N. Cheung, et al., Microstructure, tensile properties and wear resistance correlations on directionally solidified Al–Sn–(Cu; Si) alloys, J. Alloys Compd., 695(2017), p. 3621. doi: 10.1016/j.jallcom.2016.11.399
[43]	Y. Wang, X.X. Lu, N.Y. Yuan, and J.N. Ding, A novel nickel–copper alternating-deposition coating with excellent tribological and antibacterial property, J. Alloys Compd., 849(2020), art. No. 156222. doi: 10.1016/j.jallcom.2020.156222
[44]	Y.S. Zhang, Z. Han, K. Wang, and K. Lu, Friction and wear behaviors of nanocrystalline surface layer of pure copper, Wear, 260(2006), No. 9-10, p. 942. doi: 10.1016/j.wear.2005.06.010
[45]	J. Feng, K.X. Song, S.H. Liang, X.H. Guo, and Y.H. Jiang, Electrical wear of TiB₂ particle-reinforced Cu and Cu–Cr composites prepared by vacuum arc melting, Vacuum, 175(2020), art. No. 109295. doi: 10.1016/j.vacuum.2020.109295
[46]	Z. Jian, X.J. Tan, Y. Hu, L. Guo, Q.M. Zhang, and S.H. Liu, Microstructure and high power fiber laser cladding Ni60A coating, Chin. J. Nonferrous Met., 24(2015), No. 6, p. 1441.
[47]	S.S.F. de Dafé, S.D.C. Paolinelli, and A.B. Cota, Influence of thermomechanical processing on shear bands formation and magnetic properties of a 3% Si non-oriented electrical steel, J. Magn. Magn. Mater., 323(2011), No. 24, p. 3234. doi: 10.1016/j.jmmm.2011.07.015