An Al–Al interpenetrating-phase composite by 3D printing and hot extrusion

Yulin Lin; Di Wang; Chao Yang; Weiwen Zhang; Zhi Wang

doi:10.1007/s12613-022-2543-z

Volume 30 Issue 4

Apr. 2023

Turn off MathJax

Article Contents

Article Navigation > International Journal of Minerals, Metallurgy and Materials > 2023 > 30(4): 678-688

Yulin Lin, Di Wang, Chao Yang, Weiwen Zhang, and Zhi Wang, An Al–Al interpenetrating-phase composite by 3D printing and hot extrusion, Int. J. Miner. Metall. Mater., 30(2023), No. 4, pp. 678-688. https://doi.org/10.1007/s12613-022-2543-z

Cite this article as:

Yulin Lin, Di Wang, Chao Yang, Weiwen Zhang, and Zhi Wang, An Al–Al interpenetrating-phase composite by 3D printing and hot extrusion, Int. J. Miner. Metall. Mater., 30(2023), No. 4, pp. 678-688. https://doi.org/10.1007/s12613-022-2543-z

Citation:

PDF( 6193 KB)

Research Article

An Al–Al interpenetrating-phase composite by 3D printing and hot extrusion

+ Author Affiliations

Corresponding authors:
Di Wang E-mail: mewdlaser@scut.edu.cn

Zhi Wang E-mail: wangzhi@scut.edu.cn
Received: 31 March 2022; Revised: 26 August 2022; Accepted: 29 August 2022; Available online: 30 August 2022

Abstract

Abstract

We report a process route to fabricate an Al–Al interpenetrating-phase composite by combining the Al–Mg–Mn–Sc–Zr lattice structure and Al₈₄Ni₇Gd₆Co₃ nanostructured structure. The lattice structure was produced by the selective laser melting and subsequently filled with the Al₈₄Ni₇Gd₆Co₃ amorphous powder, and finally the mixture was used for hot extrusion to produce bulk samples. The results show that the composites achieve a high densification and good interface bonding due to the element diffusion and plastic deformation during hot extrusion. The bulk samples show a heterogeneous structure with a combination of honeycomb lattice structure with an average grain size of less than 1 µm and nanostructured area with a high volume fraction of nanometric intermetallics and nanograin α-Al. The heterogeneous structure leads to a bimodal mechanical zone with hard area and soft area giving rise to high strength and acceptable plasticity, where the compressive yield strength and the compressive plasticity can reach ~745 MPa and ~30%, respectively. The high strength can be explained by the rule of mixture, the grain boundary strengthening, and the back stress, while the acceptable plasticity is mainly owing to the confinement effect of the nanostructured area retarding the brittle fracture behavior.
- Al-based composites;
- heterogeneous structure;
- additive manufacturing;
- mechanical properties

FullText(HTML)

Supplements(0)

References(29)

References

[1]	Y. Mei, P.Z. Shao, M. Sun, et al., Deformation treatment and microstructure of graphene-reinforced metal matrix nanocomposites: A review of graphene post-dispersion, Int. J. Miner. Metall. Mater., 27(2020), No. 7, p. 888. doi: 10.1007/s12613-020-2048-6
[2]	C.S. Kim, K. Cho, M.H. Manjili, and M. Nezafati, Mechanical performance of particulate-reinforced Al metal-matrix composites (MMCs) and Al metal-matrix nano-composites (MMNCs), J. Mater. Sci, 52(2017), No. 23, p. 13319. doi: 10.1007/s10853-017-1378-x
[3]	E. Safary, R. Taghiabadi, and M.H. Ghoncheh, Mechanical properties of Al–15Mg₂Si composites prepared under different solidification cooling rates, Int. J. Miner. Metall. Mater., 29(2022), No. 6, p. 1249. doi: 10.1007/s12613-020-2244-4
[4]	Z. Wang, K. Georgarakis, K.S. Nakayama, et al., Microstructure and mechanical behavior of metallic glass fiber-reinforced Al alloy matrix composites, Sci. Rep., 6(2016), art. No. 24384. doi: 10.1038/srep24384
[5]	M.C. Şenel, Y. Kanca, and M. Gürbüz, Reciprocating sliding wear properties of sintered Al–B₄C composites, Int. J. Miner. Metall. Mater., 29(2022), No. 6, p. 1261. doi: 10.1007/s12613-020-2243-5
[6]	C. He, N. Zhao, C. Shi, et al., An approach to obtaining homogeneously dispersed carbon nanotubes in Al powders for preparing reinforced Al-matrix composites, Adv. Mater., 19(2007), No. 8, p. 1128. doi: 10.1002/adma.200601381
[7]	X.L. Ma, C.X. Huang, J. Moering, et al., Mechanical properties of copper/bronze laminates: Role of interfaces, Acta Mater., 116(2016), p. 43. doi: 10.1016/j.actamat.2016.06.023
[8]	X.C. Liu, Z. Liu, Y.J. Liu, et al., Achieving high strength and toughness by engineering 3D artificial nacre-like structures inTi₆Al₄V–Ti metallic composite, Composites Part B, 230(2022), art. No. 109552. doi: 10.1016/j.compositesb.2021.109552
[9]	M.Y. Zhang, Q. Yu, Z.Q. Liu, et al., 3D printed Mg–NiTi interpenetrating-phase composites with high strength, damping capacity, and energy absorption efficiency, Sci. Adv., 6(2020), No. 19, art. No. eaba5581. doi: 10.1126/sciadv.aba5581
[10]	C.W. Shao, S. Zhao, X.G. Wang, Y.K. Zhu, Z. F.Zhang, and R.O. Ritchie, Architecture of high-strength aluminum–matrix composites processed by a novel microcasting technique, NPG Asia Mater., 11(2019), art. No. 69. doi: 10.1038/s41427-019-0174-2
[11]	T. Maconachie, M. Leary, B. Lozanovski, et al., SLM lattice structures: Properties, performance, applications and challenges, Mater. Des., 183(2019), art. No. 108137. doi: 10.1016/j.matdes.2019.108137
[12]	R.D. Li, H. Chen, H.B. Zhu, M.B. Wang, C. Chen, and T.C. Yuan, Effect of aging treatment on the microstructure and mechanical properties of Al–3.02Mg–0.2Sc–0.1Zr alloy printed by selective laser melting, Mater. Des., 168(2019), art. No. 107668. doi: 10.1016/j.matdes.2019.107668
[13]	R.D. Li, M.B. Wang, Z.M. Li, P. Cao, T.C. Yuan, and H.B. Zhu, Developing a high-strength Al–Mg–Si–Sc–Zr alloy for selective laser melting: Crack-inhibiting and multiple strengthening mechanisms, Acta Mater., 193(2020), p. 83. doi: 10.1016/j.actamat.2020.03.060
[14]	Z.H. Wang, X. Lin, N. Kang, Y.L. Hu, J. Chen, and W.D. Huang, Strength-ductility synergy of selective laser melted Al–Mg–Sc–Zr alloy with a heterogeneous grain structure, Addit. Manuf., 34(2020), art. No. 101260. doi: 10.1016/j.addma.2020.101260
[15]	Z. Wang, R.T. Qu, S. Scudino, et al., Hybrid nanostructured aluminum alloy with super-high strength, NPG Asia Mater., 7(2015), No. 12, art. No. e229. doi: 10.1038/am.2015.129
[16]	R.L. Ma, C.Q. Peng, Z.Y. Cai, et al., Manipulating the microstructure and tensile properties of selective laser melted Al–Mg–Sc–Zr alloy through heat treatment, J. Alloys Compd., 831(2020), art. No. 154773. doi: 10.1016/j.jallcom.2020.154773
[17]	J.H. Zhao, L.S. Luo, X. Xue, et al., The evolution and characterizations of Al₃(Sc_xZr_1−x) phase in Al–Mg-based alloys proceeded by SLM, Mater. Sci. Eng. A, 824(2021), art. No. 141863. doi: 10.1016/j.msea.2021.141863
[18]	A. Spierings, K. Dawson, T. Heeling, et al., Microstructural features of Sc- and Zr-modified Al–Mg alloys processed by selective laser melting, Mater. Des., 115(2017), p. 52. doi: 10.1016/j.matdes.2016.11.040
[19]	Z. Wang, K.G. Prashanth, S. Scudino, et al., Tensile properties of Al matrix composites reinforced with in situ devitrified Al₈₄Gd₆Ni₇Co₃ glassy particles, J. Alloys Compd., 586(2014), p. S419. doi: 10.1016/j.jallcom.2013.04.190
[20]	Z. Wang, K.G. Prashanth, S. Scudino, et al., Effect of ball milling on structure and thermal stability of Al₈₄Gd₆Ni₇Co₃ glassy powders, Intermetallics, 46(2014), p. 97. doi: 10.1016/j.intermet.2013.11.005
[21]	Z. Wang, K.G. Prashanth, K.B. Surreddi, C. Suryanarayana, J. Eckert, and S.Scudino, Pressure-assisted sintering of Al–Gd–Ni–Co amorphous alloy powders, Materialia, 2(2018), p. 157. doi: 10.1016/j.mtla.2018.07.010
[22]	A.E. Pawlowski, Z.C. Cordero, M.R. French, et al., Damage-tolerant metallic composites via melt infiltration of additively manufactured preforms, Mater. Des., 127(2017), p. 346. doi: 10.1016/j.matdes.2017.04.072
[23]	O. Kolednik, J. Predan, F.D. Fischer, and P. Fratzl, Bioinspired design criteria for damage-resistant materials with periodically varying microstructure, Adv. Funct. Mater., 21(2011), No. 19, p. 3634. doi: 10.1002/adfm.201100443
[24]	Y.X. Geng, H. Tang, J.H. Xu, Z.J. Zhang, Y.K. Xiao, and Y. Wu, Strengthening mechanisms of high-performance Al–Mn–Mg–Sc–Zr alloy fabricated by selective laser melting, Sci. China Mater., 64(2021), No. 12, p. 3131. doi: 10.1007/s40843-021-1719-8
[25]	R.L. Ma, C.Q. Peng, Z.Y. Cai, et al., Enhanced strength of the selective laser melted Al–Mg–Sc–Zr alloy by cold rolling, Mater. Sci. Eng. A, 775(2020), art. No. 138975. doi: 10.1016/j.msea.2020.138975
[26]	S.Y. Kim, G.Y. Lee, G.H. Park, et al., High strength nanostructured Al-based alloys through optimized processing of rapidly quenched amorphous precursors, Sci. Rep., 8(2018), No. 1, art. No. 1090. doi: 10.1038/s41598-018-19337-7
[27]	X.J. Shen, C. Zhang, Y.G. Yang, and L. Liu, On the microstructure, mechanical properties and wear resistance of an additively manufactured Ti64/metallic glass composite, Addit. Manuf., 25(2019), p. 499. doi: /10.1016/j.addma.2018.12.006
[28]	Z. Tan, L. Wang, Y.F. Xue, et al., A multiple grain size distributed Al-based composite consist of amorphous/nanocrystalline, submicron grain and micron grain fabricated through spark plasma sintering, J. Alloys Compd., 737(2018), p. 308. doi: 10.1016/j.jallcom.2017.12.102
[29]	R.T. Qu and Z.F. Zhang, A universal fracture criterion for high-strength materials, Sci. Rep., 3(2013), art. No. 1117. doi: 10.1038/srep01117