SearchAluminum Alloy (2020–2024)
-
Strengthening strategy for high-performance friction stir lap welded joints based on 5083 Al alloy
2024, vol. 31, no. 11, pp. 2498-2507. doi: 10.1007/s12613-024-2847-2
-
High-strength and thermally stable TiB2-modified Al–Mn–Mg–Er–Zr alloy fabricated via selective laser melting
2024, vol. 31, no. 10, pp. 2221-2232. doi: 10.1007/s12613-024-2879-7
-
Mechanical properties and interfacial characteristics of 6061 Al alloy plates fabricated by hot-roll bonding
2024, vol. 31, no. 8, pp. 1890-1899. doi: 10.1007/s12613-023-2801-8
-
Two-stage dynamic recrystallization and texture evolution in Al–7Mg alloy during hot torsion
2024, vol. 31, no. 8, pp. 1900-1911. doi: 10.1007/s12613-024-2877-9
-
Review of Sc microalloying effects in Al–Cu alloys
2024, vol. 31, no. 5, pp. 1098-1114. doi: 10.1007/s12613-024-2841-8
-
Preheating-assisted solid-state friction stir repair of Al–Mg–Si alloy plate at different rotational speeds
2024, vol. 31, no. 4, pp. 725-736. doi: 10.1007/s12613-023-2772-9
-
Mechanical behavior and response mechanism of porous metal structures manufactured by laser powder bed fusion under compressive loading
2024, vol. 31, no. 4, pp. 737-749. doi: 10.1007/s12613-024-2865-0
-
Microstructure and mechanical properties stability of pre-hardening treatment in Al–Cu alloys for pre-hardening forming process
2024, vol. 31, no. 3, pp. 539-551. doi: 10.1007/s12613-023-2758-7
-
Effect of Ni content on the wear behavior of Al–Si–Cu–Mg–Ni/SiC particles composites
2024, vol. 31, no. 2, pp. 374-383. doi: 10.1007/s12613-023-2701-y
-
High corrosion and wear resistant electroless Ni–P gradient coatings on aviation aluminum alloy parts
2024, vol. 31, no. 1, pp. 155-164. doi: 10.1007/s12613-023-2689-3
-
Residual stress with asymmetric spray quenching for thick aluminum alloy plates
2023, vol. 30, no. 11, pp. 2200-2211. doi: 10.1007/s12613-023-2645-2
-
Anisotropy of mechanical properties of 2297-T87 Al–Li alloy thick plates
2023, vol. 30, no. 11, pp. 2212-2223. doi: 10.1007/s12613-023-2652-3
-
Corrosion, mechanical and microstructural properties of aluminum 7075–carbon nanotube nanocomposites for robots in corrosive environments
2023, vol. 30, no. 6, pp. 1140-1151. doi: 10.1007/s12613-022-2592-3
-
Repairing of exit-hole in friction-stir-spot welded joints for 2024-T4 aluminum alloy by resistance welding
2023, vol. 30, no. 4, pp. 660-669. doi: 10.1007/s12613-022-2561-x
-
Microstructure and microhardness of aluminium alloy with underwater and in-air wire-feed laser deposition
2023, vol. 30, no. 4, pp. 670-677. doi: 10.1007/s12613-022-2500-x
-
Relationship between elements migration of α-AlFeMnSi phase and micro-galvanic corrosion sensitivity of Al–Zn–Mg alloy
2023, vol. 30, no. 1, pp. 112-121. doi: 10.1007/s12613-022-2428-1
-
Hot compressive deformation of eutectic Al–17at% Cu alloy on the interface of the Cu–Al composite plate produced by horizontal continuous casting
2022, vol. 29, no. 8, pp. 1578-1588. doi: 10.1007/s12613-021-2276-4
-
Analysis of local microstructure and strengthening mechanisms in adjustable-gap bobbin tool friction stir welds of Al–Mg
2022, vol. 29, no. 8, pp. 1589-1595. doi: 10.1007/s12613-021-2254-x
-
Intermetallic growth behavior during post deformation annealing in multilayer Ti/Al/Nb composite interfaces
2022, vol. 29, no. 8, pp. 1608-1617. doi: 10.1007/s12613-021-2263-9
-
Effects of mechanical vibration on the physical, metallurgical and mechanical properties of cast A308 (LM21) aluminum alloy
2022, vol. 29, no. 6, pp. 1206-1215. doi: 10.1007/s12613-020-2209-7
-
Microstructure and mechanical properties of friction pull plug welding for 2219-T87 aluminum alloy with tungsten inert gas weld
2022, vol. 29, no. 6, pp. 1216-1224. doi: 10.1007/s12613-020-2222-x
-
Mechanical properties of Al–15Mg2Si composites prepared under different solidification cooling rates
2022, vol. 29, no. 6, pp. 1249-1260. doi: 10.1007/s12613-020-2244-4
-
Reciprocating sliding wear properties of sintered Al‒B4C composites
2022, vol. 29, no. 6, pp. 1261-1269. doi: 10.1007/s12613-020-2243-5
-
Interface microstructure and formation mechanism of ultrasonic spot welding for Al–Ti dissimilar metals
2021, vol. 28, no. 9, pp. 1506-1514. doi: 10.1007/s12613-020-2043-y
-
Bonding of compound casted Ti/Al bimetal by heat treatment
2021, vol. 28, no. 9, pp. 1515-1524. doi: 10.1007/s12613-020-2107-z
-
Direct preparation of semi-solid billets by the semi-solid isothermal heat treatment for commercial cold-rolled ZL104 aluminum alloy
2021, vol. 28, no. 7, pp. 1164-1173. doi: 10.1007/s12613-020-2067-3
-
Effect of TiB2 and Al3Ti on the microstructure, mechanical properties and fracture behaviour of near eutectic Al−12.6Si alloy
2021, vol. 28, no. 7, pp. 1174-1185. doi: 10.1007/s12613-020-2070-8
-
Solid particle erosion studies of thermally deposited alumina–titania coatings on an aluminum alloy
2021, vol. 28, no. 7, pp. 1186-1193. doi: 10.1007/s12613-020-2099-8
-
Processing and characterization of the microstructure and mechanical properties of Al6061–TiB2 composite
2021, vol. 28, no. 6, pp. 1080-1089. doi: 10.1007/s12613-021-2288-0
-
Impact of travel speed on the microstructure and mechanical properties of adjustable-gap bobbin-tool friction stir welded Al–Mg joints
2021, vol. 28, no. 4, pp. 710-717. doi: 10.1007/s12613-020-2134-9
-
Tensile properties and hot tearing susceptibility of cast Al–Cu alloys containing excess Fe and Si
2021, vol. 28, no. 4, pp. 718-728. doi: 10.1007/s12613-020-2039-7
-
Material flow behavior and microstructural evolution during refill friction stir spot welding of alclad 2A12-T4 aluminum alloy
2021, vol. 28, no. 1, pp. 131-141. doi: 10.1007/s12613-020-1998-z
-
Fabrication of robust aluminum–carbon nanotube composites using ultrasonic assembly and rolling process
2021, vol. 28, no. 1, pp. 160-167. doi: 10.1007/s12613-020-1969-4
-
Microstructure and properties of a wear resistant Al–25Si–4Cu–1Mg coating prepared by supersonic plasma spraying
2020, vol. 27, no. 9, pp. 1287-1294. doi: 10.1007/s12613-019-1950-2
-
Mechanical properties of graphene nanoplatelets reinforced 7075 aluminum alloy composite fabricated by spark plasma sintering
2020, vol. 27, no. 9, pp. 1295-1300. doi: 10.1007/s12613-020-2009-0
-
Fatigue limit assessment of a 6061 aluminum alloy based on infrared thermography and steady ratcheting effect
2020, vol. 27, no. 9, pp. 1301-1308. doi: 10.1007/s12613-019-1942-2
-
Deformation treatment and microstructure of graphene-reinforced metalmatrix nanocomposites: A review of graphene post-dispersion
2020, vol. 27, no. 7, pp. 888-899. doi: 10.1007/s12613-020-2048-6
-
Formation of interfacial Al−Ce−Cu−W amorphous layers in aluminum matrix composite through thermally driven solid-state amorphization
2020, vol. 27, no. 7, pp. 970-979. doi: 10.1007/s12613-019-1952-0
-
Non-spherical aluminum nanoparticles fabricated using picosecond laser ablation
2020, vol. 27, no. 7, pp. 980-986. doi: 10.1007/s12613-020-2032-1
-
Stress-corrosion behavior and characteristics of the friction stir welding of an AA2198-T34 alloy
2020, vol. 27, no. 6, pp. 774-782. doi: 10.1007/s12613-019-1924-4
-
Wire and arc additive manufacturing of 4043 Al alloy using a cold metal transfer method
2020, vol. 27, no. 6, pp. 783-791. doi: 10.1007/s12613-019-1930-6
-
Optimization of ECAP−RAP process for preparing semisolid billet of 6061 aluminum alloy
2020, vol. 27, no. 6, pp. 792-800. doi: 10.1007/s12613-019-1895-5
-
Effect of the initial ECAP passes on crystal texture and residual stresses of 5083 aluminum alloy
2020, vol. 27, no. 6, pp. 801-808. doi: 10.1007/s12613-020-2017-0
-
Microstructural analyses of aluminum–magnesium–silicon alloys welded by pulsed Nd: YAG laser welding
2020, vol. 27, no. 5, pp. 660-668. doi: 10.1007/s12613-020-2027-y
-
Reinforcing effect of laminate structure on the fracture toughness of Al3Ti intermetallic
2020, vol. 27, no. 5, pp. 678-686. doi: 10.1007/s12613-019-1899-1
-
Fractographic analysis of the overload effect on fatigue crack growth in 2024-T3 and 7075-T6 Al alloys
2020, vol. 27, no. 1, pp. 83-90. doi: 10.1007/s12613-019-1896-4
Submit Manuscript
E-mail alert
RSS
