Effect of austenitization temperature on microstructure and mechanical properties of low-carbon-equivalent carbidic austempered ductile iron

Vinayak Dakre; D. R. Peshwe; S. U. Pathak; Ajay Likhite

doi:10.1007/s12613-018-1625-4

Volume 25 Issue 7

Jul. 2018

Turn off MathJax

数据统计

计量

文章访问数: 499
HTML全文浏览量: 90
PDF下载量: 26
被引次数: 0

文章导航 > 矿物冶金与材料学报（英文） > 2018 > 25(7): 770-778

Vinayak Dakre, D. R. Peshwe, S. U. Pathak, and Ajay Likhite, Effect of austenitization temperature on microstructure and mechanical properties of low-carbon-equivalent carbidic austempered ductile iron, Int. J. Miner. Metall. Mater., 25(2018), No. 7, pp. 770-778. https://doi.org/10.1007/s12613-018-1625-4

Cite this article as:

Vinayak Dakre, D. R. Peshwe, S. U. Pathak, and Ajay Likhite, Effect of austenitization temperature on microstructure and mechanical properties of low-carbon-equivalent carbidic austempered ductile iron, Int. J. Miner. Metall. Mater., 25(2018), No. 7, pp. 770-778. https://doi.org/10.1007/s12613-018-1625-4

Citation:

PDF( 1105 KB)

引用本文 PDF XML SpringerLink

研究论文

Effect of austenitization temperature on microstructure and mechanical properties of low-carbon-equivalent carbidic austempered ductile iron

Department of Metallurgical & Materials Engineering, Visvesvaraya National Institute of Technology, Nagpur 440010, India

通讯作者:
Vinayak Dakre E-mail: vinayakdakre2007@gmail.com

中文摘要

The wear resistances of austempered ductile iron (ADI) were improved through introduction of a new phase (carbide) into the matrix by addition of chromium. In the present investigation, low-carbon-equivalent ductile iron (LCEDI) (CE=3.06%, and CE represents carbon-equivalent) with 2.42% chromium was selected. LCEDI was austenitized at two different temperatures (900 and 975℃) and soaked for 1 h and then quenched in a salt bath at 325℃ for 0 to 10 h. Samples were analyzed using optical microscopy and X-ray diffraction. Wear tests were carried out on a pin-on-disk-type machine. The effect of austenization temperature on the wear resistance, impact strength, and the microstructure was evaluated. A structure–property correlation based on the observations is established.

关键词:

low carbon equivalent ductile iron (LCEDI);
carbidic austempered ductile iron (CADI);
wear test;
austenitization temperature;
impact strength

Research Article

Effect of austenitization temperature on microstructure and mechanical properties of low-carbon-equivalent carbidic austempered ductile iron

+ Author Affiliations

Abstract

Abstract

The wear resistances of austempered ductile iron (ADI) were improved through introduction of a new phase (carbide) into the matrix by addition of chromium. In the present investigation, low-carbon-equivalent ductile iron (LCEDI) (CE=3.06%, and CE represents carbon-equivalent) with 2.42% chromium was selected. LCEDI was austenitized at two different temperatures (900 and 975℃) and soaked for 1 h and then quenched in a salt bath at 325℃ for 0 to 10 h. Samples were analyzed using optical microscopy and X-ray diffraction. Wear tests were carried out on a pin-on-disk-type machine. The effect of austenization temperature on the wear resistance, impact strength, and the microstructure was evaluated. A structure–property correlation based on the observations is established.
- low carbon equivalent ductile iron (LCEDI);
- carbidic austempered ductile iron (CADI);
- wear test;
- austenitization temperature;
- impact strength

FullText(HTML)

Supplements(0)

References(28)

References

[1]	Y. Tanaka and H. Kage, Development and application of austempered spheroidal graphite cast iron, Mater. Trans. JIM, 33(1992), No. 6, p. 543.
[2]	Y.S. Lerner and G.R. Kingsbury, Wear resistance properties of austempered ductile iron, J. Mater. Eng. Perform., 7(1998), No. 1, p. 48.
[3]	P. Shanmugam, P.P. Rao, K.R. Udupa, and N. Venkataraman, Effect of microstructure on the fatigue strength of an austempered ductile iron, J. Mater. Sci., 29(1994), No. 18, p. 4933.
[4]	L. Bartosiewicz, A.R. Krause, F.A. Alberts, I. Singh, and S.K. Putatunda, Influence of microstructure on high cycle fatigue behavior of austempered ductile cast iron, Mater.Charact., 30(1993), No. 4, p. 221.
[5]	J.L. Garin and R.L. Mannheim, Strain-induced martensite in ADI alloys, J. Mater. Process. Technol., 143-144(2003), p. 347.
[6]	S. Balos, I. Radisavljevic, D. Rajnovic, M. Dramicanin, S. Tabakovic, O. Eric-Cekic, and L. Sidjanin, Geometry, mechanical and ballistic properties of ADI material perforated plates, Mater. Des., 83(2015), p. 66.
[7]	R.C. Dommarco, K.J. Kozaczek, P.C. Bastias, G.T. Hahn, and C.A. Rubin, Residual stresses and retained austenite evolution in SAE 52100 steel under non-ideal rolling contact loading, Wear, 257(2004), No. 11, p. 1081.
[8]	J. Zimba, D.J. Simbi, and E. Navara, Austempered ductile iron: an alternative material for earth moving components, Cem. Concr. Compos., 25(2003), No. 6, p. 643.
[9]	L.Y. Fang and C.R. Loper Jr, Feasibility of the production of a low-cabon equivalent spheroidal graphite cast iron: a review of the literature, Am. Foundry Soc. Trans., 1991, p.313.
[10]	A. Likhite, D.R. Peshwe, and S.U. Pathak, Effect of graphite morphology on modulus of elasticity of low carbon equivalent ductile iron, Trans. Indian Inst. Met., 61(2008), No. 6, p. 497.
[11]	P. Parhad, S. Umale, A. Likhite, and J. Bhatt, Characterization of inoculated low carbon equivalent iron at lower austempering temperature, Trans. Indian Inst. Met., 65(2012), No. 5, p. 449.
[12]	A. Likhite, D.R. Peshwe, and S.U. Pathak, Development of austempered inoculated low carbon equivalent irons, Indian Foundry J., 57(2011), No. 6, p. 23.
[13]	S. Umale, A. Likhite, D.R. Peshwe, and S.U. Pathak, Wear characteristics of low carbon equivalent austempered ductile iron (ADI), Indian Foundry J., 60(2014), No. 9, p. 28.
[14]	K.L. Hayrynen and K.R. Brandenberg, Carbidic austempered ductile iron (CADI)—the new wear material, Am. Foundry Soc. Trans., 111(2003), p. 845.
[15]	J.H. Liu, G.L. Li, X.B. Zhao, X.Y. Hao, and J.J. Zhang, Effect of austempering temperature on microstructure and properties of carbidic austempered ductile iron, Adv. Mater. Res., 284-286(2011), p. 1085.
[16]	S. Laino, J.A. Sikora, and R.C. Dommarco, Development of wear resistant carbidic austempered ductile iron (CADI), Wear, 265(2008), No. 1-2, p. 1.
[17]	L. Bartosiewicz, I. Singh, F.A. Alberts, A.R. Krause, and S.K. Putatunda, The influence of chromium on mechanical properties of austempered ductile cast iron, J. Mater. Eng. Perform., 4(1995), No. 1, p. 90.
[18]	C. Suryanarayana and M. Grant Norton, X-ray Diffraction: A Practical Approach, Plenum Press, New York and London, 1998, p. 153, 223.
[19]	C.S. Roberts, Effect of carbon on the volume fractions and lattice parameters of retained austenite and martensite, JOM, 5(1953), No. 2, p. 203.
[20]	B.D. Cullity, Elements of X-Ray Diffraction, Addison-Wesley, Reading, USA, 1978, p.102.
[21]	P. Parhad, A. Likhite, J. Bhatt, and D. Peshwe, The effect of cutting speed and depth of cut on surface roughness during machining of austempered ductile iron, Trans. Indian Inst. Met., 68(2015), No. 1, p. 99.
[22]	H.O. Pierson, Handbook of Refractory Carbides and Nitrides: Properties, Characteristics, Processing and Applications, William Andrew, 1996, p. 139.
[23]	T.N. Rouns and K.B. Rundman, Constitution of austempered ductile iron and the kinetics of austempering, Am. Foundry Soc. Trans., 95(1987), p. 851.
[24]	R. Elliott, Cast Iron Technology, Butterworth-Heinemann, Oxford, 1988, p. 142.
[25]	C.H. Hsu and S.C. Lee, High strength high toughness compacted graphite cast iron, Mater. Sci. Technol., 11(1995), p. 765.
[26]	U. Batra, S. Ray, and S.R. Prabhakar, Impact properties of copper-alloyed and nickel-copper alloyed ADI, J. Mater. Eng. Perform., 16(2007), No. 4, p. 485.
[27]	U.R. Kumari and P.P. Rao, Study of wear behaviour of austempered ductile iron, J. Mater. Sci., 44(2009), p. 1082.
[28]	J.H. Yang and S.K. Putatunda, Effect of microstructure on abrasion wear behavior of austempered ductile cast iron (ADI) processed by a novel two-step austempering process, Mater. Sci. Eng. A, 406(2005), No. 1-2, p. 217.

Relative Articles

Cited By

Proportional views

数据统计

姓名
邮箱
手机号码
标题
留言内容
验证码

留言板

数据统计

分享

计量

Effect of austenitization temperature on microstructure and mechanical properties of low-carbon-equivalent carbidic austempered ductile iron

中文摘要

Effect of austenitization temperature on microstructure and mechanical properties of low-carbon-equivalent carbidic austempered ductile iron

Abstract

References

数据统计

Catalog