Effect of groove rolling on the microstructure and properties of Cu–Nb microcomposite wires

Peng-fei Wang; Ming Liang; Xiao-yan Xu; Jian-qing Feng; Cheng-shan Li; Ping-xiang Zhang; Jin-shan Li

doi:10.1007/s12613-020-2073-5

Volume 28 Issue 2

Feb. 2021

Turn off MathJax

Article Contents

Article Navigation > International Journal of Minerals, Metallurgy and Materials > 2021 > 28(2): 279-284

Peng-fei Wang, Ming Liang, Xiao-yan Xu, Jian-qing Feng, Cheng-shan Li, Ping-xiang Zhang, and Jin-shan Li, Effect of groove rolling on the microstructure and properties of Cu–Nb microcomposite wires, Int. J. Miner. Metall. Mater., 28(2021), No. 2, pp. 279-284. https://doi.org/10.1007/s12613-020-2073-5

Cite this article as:

Peng-fei Wang, Ming Liang, Xiao-yan Xu, Jian-qing Feng, Cheng-shan Li, Ping-xiang Zhang, and Jin-shan Li, Effect of groove rolling on the microstructure and properties of Cu–Nb microcomposite wires, Int. J. Miner. Metall. Mater., 28(2021), No. 2, pp. 279-284. https://doi.org/10.1007/s12613-020-2073-5

Citation:

PDF( 861 KB)

Research Article

Effect of groove rolling on the microstructure and properties of Cu–Nb microcomposite wires

+ Author Affiliations

Corresponding author:
Ping-xiang Zhang E-mail: pxzhang@c-nin.com
Received: 4 February 2020; Revised: 24 March 2020; Accepted: 13 April 2020; Available online: 16 April 2020

Abstract

Abstract

Cu–Nb microcomposite wire was successfully prepared by a groove rolling process. The effects of groove rolling on the diffraction peaks, microstructure, and properties of the Cu–Nb microcomposite were investigated and the microstructure evolutions and strengthening mechanism were discussed. The tensile strength of the Cu–Nb microcomposite wire with a diameter of 2.02 mm was greater than 1 GPa, and its conductivity reached 68% of the International Annealed Copper Standard, demonstrating the Cu–Nb microcomposite wire with high tensile strength and high conductivity after groove rolling. The results show that an appropriate groove rolling method can improve the performance of the Cu–Nb microcomposite wire.
- groove rolling;
- microstructure;
- strengthening mechanism;
- copper–niobium microcomposites

FullText(HTML)

Supplements(0)

References(21)

References

[1]	Q.Q. Sun, F. Jiang, L. Deng, H.X. Xiao, L. Li, M. Liang, and T. Peng, Uniaxial fatigue behavior of Cu–Nb micro-composite conductor, part I: Effect of peak stress and stress ratio, Int. J. Fatigue, 91(2016), p. 275. doi: 10.1016/j.ijfatigue.2015.08.025
[2]	J. Wang, R.G. Hoagland, J.P. Hirth, and A. Misra, Atomistic simulations of the shear strength and sliding mechanisms of copper–niobium interfaces, Acta Mater., 56(2008), No. 13, p. 3109. doi: 10.1016/j.actamat.2008.03.003
[3]	L. Thilly, P.O. Renault, V. Vidal, F. Lecouturier, S. Van Petegem, U. Stuhr, and H. Van Swygenhoven, Plasticity of multiscale nanofifilamentary Cu/Nb composite wires during in situ neutron diffraction: Codeformation and size effect, Appl. Phys. Lett., 88(2006), No. 19, art. No. 191906. doi: 10.1063/1.2202720
[4]	K. Han, V.J. Toplosky, R. Walsh, C. Swenson, B. Lesch, and V.I. Pantsyrnyi, Properties of high strength Cu–Nb conductor for pulsed magnet applications, IEEE Trans. Appl. Supercond., 12(2002), No. 1, p. 1176. doi: 10.1109/TASC.2002.1018611
[5]	K. Kindo, 100 T magnet developed in Osaka, Physica B, 294-295(2001), p. 585. doi: 10.1016/S0921-4526(00)00725-0
[6]	L. Thilly, S.V. Petegem, P.-O. Renault, F. Lecouturier, V. Vidal, B. Schmitt, and H. Van Swygenhoven, A new criterion for elasto-plastic transition in nanomaterials: Application to size and composite effects on Cu–Nb nanocomposite wires, Acta Mater., 57(2009), No. 11, p. 3157. doi: 10.1016/j.actamat.2009.03.021
[7]	X.C. Pan, J. Zhang, Y. Huang, and Y.C. Liu, Construction of metallurgical interface with high strength between immiscible Cu and Nb by direct bonding method, J. Alloys Compd., 723(2017), p. 1053. doi: 10.1016/j.jallcom.2017.06.314
[8]	P.F. Wang, P.X. Zhang, M. Liang, C.S. Li, and J.S. Li, Heat treatment effect on the microstructure and properties of a high-strength and high-conductivity Cu–Nb–Cu microcomposite, IEEE Trans. Appl. Supercond., 29(2019), No. 4, art. No. 6000205.
[9]	K. Shimoyama, S. Yokoyama, S. Kaneko, and F. Fujita, Effect of grooved roll profiles on microstructure evolutions of AZ31 sheets in Periodical Straining Rolling process, Mater. Sci. Eng. A, 611(2014), p. 58. doi: 10.1016/j.msea.2014.05.070
[10]	L.F. Zeng, R. Gao, Q.F. Fang, X.P. Wang, Z.M. Xie, S. Miao, T. Hao, and T. Zhang, High strength and thermal stability of bulk Cu/Ta nanolamellar multilayers fabricated by cross accumulative roll bonding, Acta Mater., 110(2016), p. 341. doi: 10.1016/j.actamat.2016.03.034
[11]	M. Knezevic and A. Bhattacharyya, Characterization of microstructure in Nb rods processed by rolling: Effect of grooved rolling die geometry on texture uniformity, Int. J. Refract. Met. Hard Mater., 66(2017), p. 44. doi: 10.1016/j.ijrmhm.2017.02.007
[12]	R.D. Nyilas and R. Spolenak, Orientation-dependent ductile-to-brittle transitions in nanostructured materials, Acta Mater., 56(2008), No. 19, p. 5627. doi: 10.1016/j.actamat.2008.07.051
[13]	S.C.V. Lim and A.D. Rollett, Length scale effects on recrystallization and texture evolution in Cu layers of a roll-bonded Cu–Nb composite, Mater. Sci. Eng. A, 520(2009), No. 1-2, p. 189. doi: 10.1016/j.msea.2009.05.020
[14]	B. Zhang, C.L. Yang, Y.X. Sun, X.L. Li, and F. Liu, The microstructure, mechanical properties and tensile deformation mechanism of rolled AlN/AZ91 composite sheets, Mater. Sci. Eng. A, 763(2019), art. No. 138118. doi: 10.1016/j.msea.2019.138118
[15]	K. Al-Fadhalah, C.N. Tomé, A.J. Beaudoin, I.M. Robertson, J.P. Hirth, and A. Misra, Modeling texture evolution during rolling of a Cu–Nb multilayered system, Philos. Mag., 85(2005), No. 13, p. 1419. doi: 10.1080/14786430412331333338
[16]	Q. Wu, W.X. Xu, and L.C. Zhang, Microstructure-based modelling of fracture of particulate reinforced metal matrix composites, Composites Part B, 163(2019), p. 384. doi: 10.1016/j.compositesb.2018.12.099
[17]	K.M. Youssef, M.A. Abaza, R.O. Scattergood, and C.C. Koch, High strength, ductility, and electrical conductivity of in-situ consolidated nanocrystalline Cu–1%Nb, Mater. Sci. Eng. A, 711(2018), p. 350. doi: 10.1016/j.msea.2017.11.060
[18]	Z. Fan, S. Xue, J. Wang, K.Y. Yu, H. Wang, and X. Zhang, Unusual size dependent strengthening mechanisms of Cu/amorphous CuNb multilayers, Acta Mater., 120(2016), p. 327. doi: 10.1016/j.actamat.2016.08.064
[19]	K. Changela, H. Krishnaswamy, and R.K. Digavalli, Development of combined groove pressing and rolling to produce ultra-fine grained Al alloys and comparison with cryorolling, Mater. Sci. Eng. A, 760(2019), p. 7. doi: 10.1016/j.msea.2019.05.088
[20]	X.Q. Shang, H.M. Zhang, Z.S. Cui, M.W. Fu, and J.B. Shao, A multiscale investigation into the effect of grain size on void evolution and ductile fracture: Experiments and crystal plasticity modeling, Int. J. Plast., 125(2020), p. 133. doi: 10.1016/j.ijplas.2019.09.009
[21]	D.P. Shen, H.B. Zhou, and W.P. Tong, Influence of deformation temperature on the microstructure and thermal stability of HPT-consolidated Cu–1%Nb alloys, J. Mater. Res. Technol., 8(2019), No. 6, p. 6396. doi: 10.1016/j.jmrt.2019.09.054