Influence of introducing Zr, Ti, Nb and Ce elements on externally solidified crystals and mechanical properties of high-pressure die-casting Al–Si alloy

Junjie Li; Wenbo Yu; Zhenyu Sun; Weichen Zheng; Liangwei Zhang; Yanling Xue; Wenning Liu; Shoumei Xiong

doi:10.1007/s12613-024-2882-z

Volume 32 Issue 1

Jan. 2025

Turn off MathJax

Article Contents

Article Navigation > International Journal of Minerals, Metallurgy and Materials > 2025 > 32(1): 147-153

Junjie Li, Wenbo Yu, Zhenyu Sun, Weichen Zheng, Liangwei Zhang, Yanling Xue, Wenning Liu, and Shoumei Xiong, Influence of introducing Zr, Ti, Nb and Ce elements on externally solidified crystals and mechanical properties of high-pressure die-casting Al–Si alloy, Int. J. Miner. Metall. Mater., 32(2025), No. 1, pp. 147-153. https://doi.org/10.1007/s12613-024-2882-z

Cite this article as:

Junjie Li, Wenbo Yu, Zhenyu Sun, Weichen Zheng, Liangwei Zhang, Yanling Xue, Wenning Liu, and Shoumei Xiong, Influence of introducing Zr, Ti, Nb and Ce elements on externally solidified crystals and mechanical properties of high-pressure die-casting Al–Si alloy, Int. J. Miner. Metall. Mater., 32(2025), No. 1, pp. 147-153. https://doi.org/10.1007/s12613-024-2882-z

Citation:

PDF( 4591 KB)

Research Article

Influence of introducing Zr, Ti, Nb and Ce elements on externally solidified crystals and mechanical properties of high-pressure die-casting Al–Si alloy

+ Author Affiliations

Corresponding authors:
Wenbo Yu E-mail: wbyu@bjtu.edu.cn

Shoumei Xiong E-mail: smxiong@tsinghua.edu.cn
Received: 1 December 2023; Revised: 12 March 2024; Accepted: 13 March 2024; Available online: 15 March 2024

Abstract

Abstract

High pressure die casting (HPDC) AlSi10MnMg alloy castings are widely used in the automobile industry. Mg can optimize the mechanical properties of castings through heat treatment, while the release of thermal stress arouses the deformation of large integrated die-castings. Herein, the development of non-heat treatment Al alloys is becoming the hot topic. In addition, HPDC contains externally solidified crystals (ESCs), which are detrimental to the mechanical properties of castings. To achieve high strength and toughness of non-heat treatment die-casting Al–Si alloy, we used AlSi9Mn alloy as matrix with the introduction of Zr, Ti, Nb, and Ce. Their influences on ESCs and mechanical properties were systematically investigated through three-dimensional reconstruction and thermodynamic simulation. Our results reveal that the addition of Ti increased ESCs’ size and porosity, while the introduction of Nb refined ESCs and decreased porosity. Meanwhile, large-sized Al₃(Zr,Ti) phases formed and degraded the mechanical properties. Subsequent introduction of Ce resulted in the poisoning effect and reduced mechanical properties.
- aluminium alloy;
- high-pressure die-casting;
- externally solidified crystals;
- non-heat treatment

FullText(HTML)

Supplements(0)

References(26)

References

[1]	L. Zhu, F. Qiu, Q. Zou, et al., Multiscale design of α-Al, eutectic silicon and Mg₂Si phases in Al–Si–Mg alloy manipulated by in situ nanosized crystals, Mater. Sci. Eng. A, 802(2021), art. No. 140627. doi: 10.1016/j.msea.2020.140627
[2]	W.J. Liu, Y.D. Li, Z.X. Song, X.M. Luo, H.K. Yang, and G.L. Bi, Effect of trace Sr+Ce compound modification on microstructure, thermal conductivity and mechanical properties of AlSi10MnMg alloy, Chin. J. Nonferrous Met., 32(2022), No. 2, p. 332.
[3]	X.Y. Jiao, Y.X. Liu, J. Wang, et al., The microstructure characteristics and fracture behavior of the polyhedral primary iron-rich phase and plate-shaped eutectic iron-rich phase in a high-pressure die-cast AlSi10MnMg alloy, J. Mater. Sci. Technol., 140(2023), p. 201. doi: 10.1016/j.jmst.2022.09.014
[4]	X.Y. Jiao, P.Y. Wang, Y.X. Liu, et al., Fracture behavior of a high pressure die casting AlSi10MnMg alloy with varied porosity levels, J. Mater. Res. Technol., 25(2023), p. 1129. doi: 10.1016/j.jmrt.2023.05.281
[5]	J.M. Sanchez, M. Arribas, H. Galarraga, M. Garcia de Cortazar, M. Ellero, and F. Girot, Effects of Mn addittion, cooling rate and holding temperature on the modification and purification of iron-rich compounds in AlSi10MnMg(Fe) alloy, Heliyon, 9(2023), No. 2, art. No. e13005. doi: 10.1016/j.heliyon.2023.e13005
[6]	Y. Liu, B.H. Duan, G.Y. Chen, et al., Development history and future prospect of die cast aluminum alloy, Mater. Rep., 37(2023), No. Z2, art. No. 23030025.
[7]	A.A. Luo, A.K. Sachdev, and D. Apelian, Alloy development and process innovations for light metals casting, J. Mater. Process. Technol., 306(2022), art. No. 117606. doi: 10.1016/j.jmatprotec.2022.117606
[8]	W.P. Liu, C.H. Zhao, T. Peng, Z.W. Zhang, and A.P. Wan, Simulation-assisted multi-process integrated optimization for greentelligent aluminum casting, Appl. Energy, 336(2023), art. No. 120831. doi: 10.1016/j.apenergy.2023.120831
[9]	Y.F. Zhang, X.W. Song, H. Wu, et al., Development and application of integrated die casting technology in shock tower of body, Foundry, 72(2023), No. 4, p. 437.
[10]	X.P. Niu, B.H. Hu, I. Pinwill, and H. Li, Vacuum assisted high pressure die casting of aluminium alloys, J. Mater. Process. Technol., 105(2000), No. 1-2, p. 119. doi: 10.1016/S0924-0136(00)00545-8
[11]	H.X. Cao, C.C. Wang, Q.Y. Shan, et al., Kinetic analysis of pore formation in die-cast metals and influence of absolute pressure on porosity, Vacuum, 168(2019), art. No. 108828. doi: 10.1016/j.vacuum.2019.108828
[12]	Y.J. Zhang, E. Lordan, K. Dou, S.H. Wang, and Z.Y. Fan, Influence of porosity characteristics on the variability in mechanical properties of high pressure die casting (HPDC) AlSi7MgMn alloys, J. Manuf. Process., 56(2020), p. 500. doi: 10.1016/j.jmapro.2020.04.071
[13]	C.S. Ma, W.B. Yu, T.T. Zhang, Z.H. Zhang, Y.H. Ma, and S.M. Xiong, The effect of slow shot speed and casting pressure on the 3D microstructure of high pressure die casting AE44 magnesium alloy, J. Magnes. Alloys, 11(2023), No. 2, p. 753. doi: 10.1016/j.jma.2021.09.011
[14]	Z.D. Li, N. Limodin, A. Tandjaoui, P. Quaegebeur, P. Osmond, and D. Balloy, Influence of Sr, Fe and Mn content and casting process on the microstructures and mechanical properties of AlSi7Cu3 alloy, Mater. Sci. Eng. A, 689(2017), p. 286. doi: 10.1016/j.msea.2017.02.041
[15]	L.F. Zhang, J.W. Gao, L.N.W. Damoah, and D.G. Robertson, Removal of iron from aluminum: A review, Miner. Process. Extr. Metall. Rev., 33(2012), No. 2, p. 99. doi: 10.1080/08827508.2010.542211
[16]	S.X. Ji, W.C. Yang, F. Gao, D. Watson, and Z.Y. Fan, Effect of iron on the microstructure and mechanical property of Al–Mg–Si–Mn and Al–Mg–Si diecast alloys, Mater. Sci. Eng. A, 564(2013), p. 130. doi: 10.1016/j.msea.2012.11.095
[17]	W.C. Yang, F. Gao, and S.X. Ji, Formation and sedimentation of Fe-rich intermetallics in Al–Si–Cu–Fe alloy, Trans. Nonferrous Met. Soc. China, 25(2015), No. 5, p. 1704. doi: 10.1016/S1003-6326(15)63776-1
[18]	T. Xiao, G.Q. Lv, Y. Bao, W.C. Duo, L. Xu, and W.H. Ma, Electromagnetic separation of coarse Al–Si melts: The migration behavior of iron-rich phase and continuous growth of primary silicon, J. Alloys Compd., 819(2020), art. No. 153006. doi: 10.1016/j.jallcom.2019.153006
[19]	M. Timpel, N. Wanderka, R. Schlesiger, et al., The role of strontium in modifying aluminium–silicon alloys, Acta Mater., 60(2012), No. 9, p. 3920. doi: 10.1016/j.actamat.2012.03.031
[20]	H.Q. Duan, Z.Y. Han, and B. Wang, Research progress on non-heat treatment die-casting aluminum alloy for automotive structural parts, Autom. Technol. Mater., (2022), No. 5, p. 1.
[21]	X.Y. Jiao, Y.F. Zhang, J. Wang, et al., Characterization of externally solidified crystals in a high-pressure die-cast AlSi10MnMg alloy and their effect on porosities and mechanical properties, J. Mater. Process. Technol., 298(2021), art. No. 117299. doi: 10.1016/j.jmatprotec.2021.117299
[22]	W.B. Yu, C.S. Ma, Y.H. Ma, and S.M. Xiong, Correlation of 3D defect-band morphologies and mechanical properties in high pressure die casting magnesium alloy, J. Mater. Process. Technol., 288(2021), art. No. 116853. doi: 10.1016/j.jmatprotec.2020.116853
[23]	K.G. Basavakumar, P.G. Mukunda, and M. Chakraborty, Influence of grain refinement and modification on microstructure and mechanical properties of Al–7Si and Al–7Si–2.5Cu cast alloys, Mater. Charact., 59(2008), No. 3, p. 283. doi: 10.1016/j.matchar.2007.01.011
[24]	F. Wang, D. Qiu, Z.L. Liu, J. Taylor, M. Easton, and M.X. Zhang, Crystallographic study of Al₃Zr and Al₃Nb as grain refiners for Al alloys, Trans. Nonferrous Met. Soc. China, 24(2014), No. 7, p. 2034. doi: 10.1016/S1003-6326(14)63309-4
[25]	Z.N. Chen, H.J. Kang, G.H. Fan, et al., Grain refinement of hypoeutectic Al–Si alloys with B, Acta Mater., 120(2016), p. 168. doi: 10.1016/j.actamat.2016.08.045
[26]	J.H. Ding, C. Lu, Y.J. Sun, C.X. Cui, and E.T. Zhao, Refining and modification effects of (Al, Zr, Si)–Al₄Sr on Al–7Si–0.5Mg alloy, J. Mater. Res. Technol., 15(2021), p. 1604. doi: 10.1016/j.jmrt.2021.09.006